Equipment Use and Repair

3,282 topics in this forum

1. Sitter firing gauge

   By LakinK, March 21, 2019
   • 4 replies
   • 413 views
   • 
   • neilestrick
   • March 22, 2019

2. Raku-pit firing -kiln building and trying new ideas

   By Mark C., March 15, 2019
   • 9 replies
   • 572 views
   • 
   • Sofusryge
   • March 20, 2019

3. Err 1

   By Skip, December 26, 2018
   • 17 replies
   • 841 views
   • 
   • Skip
   • March 20, 2019

4. Kiln conversion 240v to 208v

   By Magnet, March 17, 2019
   • 8 replies
   • 3.4k views
   • 
   • Bill Kielb
   • March 18, 2019

5. RETRO FITTING A KILN SITTER? 1 2

   By Julie P, March 14, 2019   

   • kiln
   • 36 replies
   • 2.5k views
   • 
   • Julie P
   • March 18, 2019

6. Best L&L kilns for home use

   By AssirStudio, March 15, 2019
   • 3 replies
   • 697 views
   • 
   • Roberta12
   • March 15, 2019

7. Ball mill - ceramic ball sizing

   By jafa5, March 13, 2019   

   • mill
   • 2 replies
   • 246 views
   • 
   • jafa5
   • March 14, 2019

8. Do these elements need replacing?

   By lukeseall, March 11, 2019   

   • kiln elements
   • elements
   • 12 replies
   • 495 views
   • 
   • lukeseall
   • March 13, 2019

9. Increasing the maximum speed of a Bailey wheel

   By Min, March 5, 2019
   • 3 replies
   • 690 views
   • 
   • neilestrick
   • March 9, 2019

10. Trouble shooting kiln elements

    By gregory.hammond, March 9, 2019
    • 4 replies
    • 684 views
    • 
    • neilestrick
    • March 9, 2019

11. Cleaning a pug mill. How clean does it need to be?

    By g-bus, March 8, 2019
    • 9 replies
    • 1.8k views
    • 
    • Pres
    • March 8, 2019

12. brent c, the the wheel is spinning regardless

    By ilana, March 5, 2019
    • 9 replies
    • 487 views
    • 
    • ilana
    • March 8, 2019

13. Cleaning your motor brushes

    By Mark C., March 6, 2019
    • 0 replies
    • 181 views
    • 
    • Mark C.
    • March 6, 2019

14. Replaced older Brent Model C control box with newer Classic one

    By Jeremie, March 5, 2019
    • 1 reply
    • 268 views
    • 
    • Mark C.
    • March 5, 2019

15. Buying new kiln

    By ShaoGG, March 5, 2019
    • 3 replies
    • 287 views
    • 
    • Benzine
    • March 5, 2019

16. Advice on buying a used wheel

    By Lupe, March 4, 2019   

    • usedwheel
    • 3 replies
    • 236 views
    • 
    • Lupe
    • March 4, 2019

17. Some questions on building a DIY spray booth fan

    By Saki, March 4, 2019
    • 13 replies
    • 5.6k views
    • 
    • Bill Kielb
    • March 4, 2019

18. Kiln lid propped

    By Coco, March 3, 2019
    • 4 replies
    • 554 views
    • 
    • Coco
    • March 4, 2019

19. Dough mixer for mixing stain into porcelain

    By Liz Swain, March 3, 2019   

    • colored clay
    • porcelain
    • (and 2 more)

      Tagged with:

      • colored clay
      • porcelain
      • mason stains
      • wedging
    • 9 replies
    • 636 views
    • 
    • Liz Swain
    • March 4, 2019

20. cress FX 27 P kiln

    By Art Andersen, February 27, 2019
    • 3 replies
    • 483 views
    • 
    • Chilly
    • February 28, 2019

21. Firing Disaster? Fired For 20 Hours - 9 Hour Soak? 1 2 3 4

    By WildCelticRose, February 19, 2015   

    • firing
    • overfiring
    • (and 4 more)

      Tagged with:

      • firing
      • overfiring
      • over
      • kiln
      • electric
      • soak
    • 98 replies
    • 12.4k views
    • 
    • Carrick
    • February 28, 2019

22. Advancer shelves and cooling in Electric

    By Motor, February 17, 2019   

    • electric kiln
    • advancer
    • (and 1 more)

      Tagged with:

      • electric kiln
      • advancer
      • cooling
    • 10 replies
    • 1.1k views
    • 
    • Mark C.
    • February 26, 2019

23. Evenheat kiln 5320XL, sitter kiln model k

    By Rhags, February 22, 2019
    • 8 replies
    • 2.9k views
    • 
    • Bill Kielb
    • February 26, 2019

24. Heat output from new kiln

    By robinelise66, February 23, 2019
    • 14 replies
    • 989 views
    • 
    • liambesaw
    • February 25, 2019

25. L&L Genesis Control Initial Firing

    By robinelise66, February 19, 2019
    • 7 replies
    • 2k views
    • 
    • robinelise66
    • February 23, 2019