Equipment Use and Repair

3,280 topics in this forum

1. Pugmill won't extrude through dies

   By Pugmill Won't Extrude, May 1, 2019
   • 3 replies
   • 277 views
   • 
   • Mark C.
   • May 2, 2019

2. Help with slab roller

   By tinypieces, May 2, 2019   

   • slab roller
   • 1 reply
   • 345 views
   • 
   • Mark C.
   • May 2, 2019

3. Diamond Grinding Disk for Wheel Head

   By Joseph Fireborn, May 1, 2019
   • 12 replies
   • 1.2k views
   • 
   • Joseph Fireborn
   • May 1, 2019

4. Geil kiln to my collection?

   By Mark C., May 1, 2019
   • 3 replies
   • 388 views
   • 
   • neilestrick
   • May 1, 2019

5. There are no shortcuts in art

   By Bobby, May 1, 2019
   • 0 replies
   • 199 views
   • 
   • Bobby
   • May 1, 2019

6. Who can tell me that material?

   By leopold, April 30, 2019
   • 17 replies
   • 650 views
   • 
   • Hulk
   • May 1, 2019

7. Fail message - thermocouple replaced

   By Alanna, April 30, 2019
   • 2 replies
   • 570 views
   • 
   • neilestrick
   • April 30, 2019

8. Choosing an oval kiln: Skutt vs Cone Art

   By Stillwater, April 30, 2019   

   • kilns
   • 1 reply
   • 1.8k views
   • 
   • Bill Kielb
   • April 30, 2019

9. Total Newbie Struggling With Gare 1820A With Kiln Sitter Lt 3Ks

   By janeartypants, July 22, 2015   

   • manual kiln
   • Gare kiln 1820A
   • (and 2 more)

     Tagged with:

     • manual kiln
     • Gare kiln 1820A
     • kiln settings
     • Fire-Right
   • 6 replies
   • 3.3k views
   • 
   • Dick White
   • April 29, 2019

10. Gas kiln and cement backer boards

    By Luitreth, April 25, 2019
    • 14 replies
    • 2k views
    • 
    • Luitreth
    • April 28, 2019

11. Duncan Teacher kiln, smoking when fired

    By happypotter1981, April 26, 2019
    • 5 replies
    • 673 views
    • 
    • Bill Kielb
    • April 26, 2019

12. Talisman studio sieve $200 really?

    By NoArtist, April 26, 2019
    • 6 replies
    • 756 views
    • 
    • Mark C.
    • April 26, 2019

13. kiln Stand

    By Maj0rMalfunct10n, April 25, 2019
    • 5 replies
    • 872 views
    • 
    • Bill Kielb
    • April 26, 2019

14. Torchbearer

    By ml_cain3, April 25, 2019
    • 3 replies
    • 273 views
    • 
    • neilestrick
    • April 25, 2019

15. use of a duncan kiln

    By annevej, April 25, 2019   

    • duncan kiln manual
    • 1 reply
    • 363 views
    • 
    • Mark C.
    • April 25, 2019

16. BASO valve schematic? Troubleshooting?

    By Tim Allen, April 16, 2019
    • 19 replies
    • 3.3k views
    • 
    • Bill Kielb
    • April 24, 2019

17. Snap-In Thermocouple -- removal tips?

    By Tim Allen, April 16, 2019
    • 3 replies
    • 1.1k views
    • 
    • Tim Allen
    • April 24, 2019

18. kiln buying

    By JanineRumble, April 10, 2019
    • 17 replies
    • 1k views
    • 
    • Stephen
    • April 23, 2019

19. Hydrocal- lightweight or high-strength?

    By Elise, April 19, 2019
    • 15 replies
    • 934 views
    • 
    • CactusPots
    • April 23, 2019

20. Chain drive for slab roller

    By NoArtist, April 19, 2019
    • 6 replies
    • 1.2k views
    • 
    • NoArtist
    • April 22, 2019

21. Pug mills: max water content, flocculation. plasticity?

    By brookst, April 18, 2019
    • 3 replies
    • 296 views
    • 
    • CactusPots
    • April 20, 2019

22. Shimpo VL Whisper control board

    By RuthB, April 19, 2019   

    • shimpo
    • wheels
    • (and 1 more)

      Tagged with:

      • shimpo
      • wheels
      • controls
    • 2 replies
    • 1.1k views
    • 
    • Mark C.
    • April 20, 2019

23. Humming sound coming from my wheel at particular speed

    By Chillybiscuits, April 18, 2019
    • 1 reply
    • 574 views
    • 
    • neilestrick
    • April 18, 2019

24. Kiln Temp Too High...Even At Lowest Setting?

    By ghetto3jon, April 11, 2019
    • 22 replies
    • 2.1k views
    • 
    • ghetto3jon
    • April 18, 2019

25. Failed to reach temperature

    By Momo, April 15, 2019   

    • firing
    • temperature
    • 8 replies
    • 442 views
    • 
    • JohnnyK
    • April 16, 2019