Equipment Use and Repair

3,276 topics in this forum

1. Paragon A66B Questions 1 2

   By Neosquid, November 28, 2021
   • 49 replies
   • 2.9k views
   • 
   • Hulk
   • December 25, 2022

2. best control switch for a small test kiln 8x8x8

   By STONEWARECAFE, December 23, 2022
   • 2 replies
   • 206 views
   • 
   • neilestrick
   • December 23, 2022

3. Skutt Lid Brace Placement

   By mandyk, December 13, 2022
   • 9 replies
   • 750 views
   • 
   • Jeff Longtin
   • December 19, 2022

4. Cold weather firing with propane

   By Kelly in AK, December 18, 2022
   • 2 replies
   • 275 views
   • 
   • Kelly in AK
   • December 18, 2022

5. Is it possible to replace kiln elements dangling all over the place?

   By SaltAirAllison, December 14, 2022
   • 5 replies
   • 528 views
   • 
   • SaltAirAllison
   • December 18, 2022

6. Replacing 2.5" bricks with 3"?

   By tkw954, December 15, 2022
   • 3 replies
   • 309 views
   • 
   • Mark C.
   • December 15, 2022

7. Vent duct heat and safety in basement

   By MCB, November 27, 2022
   • 8 replies
   • 248 views
   • 
   • Cobraone
   • December 15, 2022

8. Skutt 822 wire gauge size vs. breaker size.

   By cadenrank, December 13, 2022
   • 10 replies
   • 598 views
   • 
   • Mark C.
   • December 14, 2022

9. How to avoid kiln debris? and how to prevent kiln shelves from staining when using cobalt blue?

   By Gazal, December 12, 2022
   • 2 replies
   • 398 views
   • 
   • Babs
   • December 13, 2022

10. Just How Old Is Too Old For A Kiln? 1 2 3

    By Stephen, September 16, 2016
    • 53 replies
    • 23.7k views
    • 
    • neilestrick
    • December 12, 2022

11. Looking to buy a new Front load electric kiln

    By Elmoclayman, November 30, 2022
    • 7 replies
    • 506 views
    • 
    • Piedmont Pottery
    • December 10, 2022

12. Replacing Bearings on an OLD Lockerbie Wheel

    By AveryO, April 24, 2020   

    • lockerbie
    • bearings
    • (and 1 more)

      Tagged with:

      • lockerbie
      • bearings
      • repair wheel
    • 15 replies
    • 2.1k views
    • 
    • jason3545
    • December 9, 2022

13. settings on the knob

    By Yvonne51, December 7, 2022
    • 1 reply
    • 104 views
    • 
    • neilestrick
    • December 7, 2022

14. Alsager parts

    By Nics, February 14, 2021
    • 5 replies
    • 720 views
    • 
    • neilestrick
    • December 4, 2022

15. 4 prong kiln power cord to 3 prong?

    By AngelaAngela, December 4, 2022
    • 2 replies
    • 563 views
    • 
    • Hulk
    • December 4, 2022

16. L&L Kiln firing incredibly slow

    By MpotterNC, December 4, 2022
    • 1 reply
    • 201 views
    • 
    • neilestrick
    • December 4, 2022

17. Elements resistance testing

    By Johnmicheal, November 30, 2022   

    • elements
    • resistance
    • (and 1 more)

      Tagged with:

      • elements
      • resistance
      • testing
    • 5 replies
    • 232 views
    • 
    • Johnmicheal
    • December 4, 2022

18. Kiln got rained on

    By Kodian, November 18, 2022
    • 4 replies
    • 523 views
    • 
    • Kodian
    • December 3, 2022

19. Soldner Wheels - Does anyone have experience?

    By Adam Dippel, January 31, 2021
    • 12 replies
    • 1.5k views
    • 
    • Hulk
    • December 3, 2022

20. TC2 failure on a controller?

    By blackhandedone, December 2, 2022
    • 1 reply
    • 193 views
    • 
    • Bill Kielb
    • December 2, 2022

21. THermocouple Is reading hotter than it should

    By Elmoclayman, November 29, 2022
    • 13 replies
    • 486 views
    • 
    • PeterH
    • November 30, 2022

22. Slow Glaze Fire

    By Bob Gonzales, November 29, 2022
    • 3 replies
    • 234 views
    • 
    • Jeff Longtin
    • November 29, 2022

23. Kiln furniture

    By Cherry, November 24, 2022
    • 5 replies
    • 330 views
    • 
    • Mark C.
    • November 26, 2022

24. Skutt kiln skipped a hold - no error code displayed

    By JRW, November 23, 2022
    • 9 replies
    • 485 views
    • 
    • Dick White
    • November 26, 2022

25. AAARGH SHIMPO you changed EVERYTHING!

    By Pyewackette, April 23, 2022
    • 13 replies
    • 1.6k views
    • 
    • Bill Kielb
    • November 25, 2022