Jump to content

Equipment Use and Repair

Use and maintenance of kilns, wheels, pug mills, slab rollers, etc. 
Moderated by: Neil Estrick

3,276 topics in this forum

  1. using aluminum foil over kiln lid to reduce radiant heat loss.... could it?

    By Christiane77,
    • 13 replies
    • 1.1k views

  2. Old Shimpo RingCone Popet Stuck Clockwise

    By brettwulc,
    • 2 replies
    • 303 views

  3. Ventmaster, should I turn off before top temp reached?

    By Anna M,
    • 4 replies
    • 355 views

  4. Firing damp shelves

    By Babs,
    • 2 replies
    • 339 views

  5. Nidec Pugmill not releasing pugs.

    By ARTeacher,   
    • 3 replies
    • 335 views

  6. New Skutt wheel - lots of questions and issues?

    By perkybus,
    • 9 replies
    • 608 views

  7. kiln help - Duncan EA-820

    By jjj,
    • 3 replies
    • 347 views

  8. Maintaining floor of Noborigama (brick)

    By Suzana Lisanti,
    • 3 replies
    • 330 views

  9. Firing blind

    By Mark C.,
    • 14 replies
    • 357 views

  10. How to replace a wheel head on a brent model C?

    By Maggiez,
    • 1 reply
    • 371 views

  11. Do you grease a new wheel head if so wear and with what?

    By Maggiez,
    • 3 replies
    • 293 views

  12. 15amp vs 20amp receptacle for 115v kiln

    By perkybus,
    • 1 reply
    • 174 views

  13. Drilling holes through older 14" wheel head

    By Jen WC,
    • 5 replies
    • 430 views

  14. Duncan EA820 - Replacement Kiln Bricks

    By MikP,
    • 1 reply
    • 257 views

  15. Pacifica 800 wheel head will not completely stop.

    By aplace,
    • 3 replies
    • 294 views

  16. Kiln lid repair

    By Brenda DeMass,
    • 1 reply
    • 354 views

  17. Manual Kilnsetter Skutt 231-18 Conversion to Bartlett Genesis Digital Controller with Solid State Realys

    By Dana Stripe,   
    • 10 replies
    • 909 views

  18. Skutt Error Code 1, what to troubleshoot first?

    By Lucybeaumont,
    • 22 replies
    • 1.3k views

  19. Genesis 2.0 controller and Thermocouple errors

    By Velk,
    • 3 replies
    • 493 views

  20. Kiln question

    By Bam2015,
    • 4 replies
    • 307 views

  21. Need advice/suggestions on a COMPLETE retrofit of older L&L J2927 kiln 1 2

    By starrs_ridge,
    • 30 replies
    • 893 views

  22. Help wiring a han 15D plug to a IPCO Studio 3000 kiln controller

    By ShanRums,
    • 1 reply
    • 213 views

  23. Skutt GlazeTech kiln issues. Relay still clicks but output voltage not as expected? 1 2 3

    By cadenrank,
    • 54 replies
    • 1.5k views

  24. Information: “Custom-Bilt” kiln

    By BJ Santora,
    • 0 replies
    • 165 views

  25. Slab Roller Issue

    By GLR,
    • 13 replies
    • 860 views
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept