Equipment Use and Repair

3,278 topics in this forum

1. Transporting CoreLite shelves from store to studio?

   By not a bot, July 7, 2022
   • 4 replies
   • 265 views
   • 
   • not a bot
   • July 7, 2022

2. First firing for rebuilt kiln: Fire as new kiln or just as new elements?

   By g-bus, July 6, 2022
   • 1 reply
   • 269 views
   • 
   • neilestrick
   • July 6, 2022

3. Low voltage issue

   By Didiho, July 3, 2022
   • 8 replies
   • 330 views
   • 
   • Dick White
   • July 6, 2022

4. Temporary/moveable venting for a kiln?

   By AlexMB, July 4, 2022
   • 8 replies
   • 689 views
   • 
   • Pres
   • July 5, 2022

5. Cress E-23 E-1 error - elements not all firing- could this be relay?

   By terraworks57, July 4, 2022   

   • relay
   • cress kiln
   • (and 2 more)

     Tagged with:

     • relay
     • cress kiln
     • elements
     • e-1 error
   • 2 replies
   • 278 views
   • 
   • terraworks57
   • July 4, 2022

6. Duncan EA-820 not reaching temp

   By jessb, July 4, 2022
   • 0 replies
   • 117 views
   • 
   • jessb
   • July 4, 2022

7. Olympic Model 1818 mystery used kiln

   By Maskedmaven, October 16, 2020   

   • used kiln
   • 14 replies
   • 1.6k views
   • 
   • neilestrick
   • July 4, 2022

8. Vintage Dawson Kiln Operation

   By Goyo, July 3, 2022
   • 1 reply
   • 199 views
   • 
   • neilestrick
   • July 4, 2022

9. kiln operation. DD12 Olympic natural gas

   By Mudfish, June 30, 2022
   • 11 replies
   • 529 views
   • 
   • Bill Kielb
   • July 3, 2022

10. Kiln sitter timers

    By cadenrank, June 29, 2022
    • 3 replies
    • 377 views
    • 
    • cadenrank
    • June 29, 2022

11. Dremel diamond grinding bits

    By rdrr, June 29, 2022
    • 1 reply
    • 304 views
    • 
    • Piedmont Pottery
    • June 29, 2022

12. Pugmill Vacuum Pump Fluttering & gasket suggestions?

    By Megga, June 22, 2022   

    • pugmill
    • de-air
    • (and 4 more)

      Tagged with:

      • pugmill
      • de-air
      • de-airing
      • vacuum
      • pump
      • venco
    • 4 replies
    • 751 views
    • 
    • Bill Kielb
    • June 28, 2022

13. Cement on lid of kiln beginning to peel — any recommended treatment?

    By Polydeuces, June 26, 2022
    • 11 replies
    • 283 views
    • 
    • Bill Kielb
    • June 28, 2022

14. Seeking info on JW Good Kiln

    By Brenda Lucas, August 1, 2021
    • 3 replies
    • 1.2k views
    • 
    • Bill M.
    • June 28, 2022

15. Old Brent b resistor 1 2

    By Macke, March 25, 2022
    • 29 replies
    • 1k views
    • 
    • RobertCorlett
    • June 27, 2022

16. Brent wheelhead removal trouble

    By kylies.clay, June 20, 2022
    • 9 replies
    • 1.1k views
    • 
    • Mark C.
    • June 27, 2022

17. LnL Quad Element Question?

    By not a bot, June 26, 2022
    • 5 replies
    • 376 views
    • 
    • not a bot
    • June 26, 2022

18. LNL e23T-3 with Solid State Relay Option

    By not a bot, June 25, 2022
    • 7 replies
    • 423 views
    • 
    • oldlady
    • June 26, 2022

19. Question about a statement regarding APM elements

    By not a bot, June 23, 2022
    • 10 replies
    • 691 views
    • 
    • oldlady
    • June 25, 2022

20. Built a Kiln on Joe Finch's model. The temperature is stuck at 600 degree celsius.

    By Rupsa Nath, January 13, 2020
    • 24 replies
    • 2k views
    • 
    • Matt Garrett
    • June 24, 2022

21. Kiln vent location

    By ut_potter, June 22, 2022
    • 3 replies
    • 244 views
    • 
    • ut_potter
    • June 23, 2022

22. Cink user manual, instructions

    By Bam2015, March 26, 2022
    • 5 replies
    • 567 views
    • 
    • Bam2015
    • June 20, 2022

23. How to re-tighten the bolts on Shimpo RK-55

    By Linchimb, May 30, 2022
    • 7 replies
    • 528 views
    • 
    • Linchimb
    • June 20, 2022

24. Old Pacifica GT 400 Wheel Bearing Replacement

    By Greg Lamont, June 18, 2022
    • 5 replies
    • 719 views
    • 
    • Mark C.
    • June 20, 2022

25. Olympic 2827HE kiln electrical problem

    By LadyLumpsClay, June 16, 2022
    • 5 replies
    • 286 views
    • 
    • LadyLumpsClay
    • June 18, 2022