Jump to content

Equipment Use and Repair

Use and maintenance of kilns, wheels, pug mills, slab rollers, etc. 
Moderated by: Neil Estrick

3,282 topics in this forum

  1. Kiln question

    By Bam2015,
    • 4 replies
    • 311 views

  2. Need advice/suggestions on a COMPLETE retrofit of older L&L J2927 kiln 1 2

    By starrs_ridge,
    • 30 replies
    • 915 views

  3. Help wiring a han 15D plug to a IPCO Studio 3000 kiln controller

    By ShanRums,
    • 1 reply
    • 215 views

  4. Skutt GlazeTech kiln issues. Relay still clicks but output voltage not as expected? 1 2 3

    By cadenrank,
    • 54 replies
    • 1.6k views

  5. Information: “Custom-Bilt” kiln

    By BJ Santora,
    • 0 replies
    • 166 views

  6. Slab Roller Issue

    By GLR,
    • 13 replies
    • 869 views

  7. repair on an old kiln

    By jessiep.246,   
    • 6 replies
    • 345 views

  8. olympic kiln going in and have questions?

    By sdwolff989,
    • 7 replies
    • 420 views

  9. Sentry 2.0 controller

    By drhender,
    • 11 replies
    • 512 views

  10. Amaco Excel 257 SF Elements

    By Amandafern,   
    • 2 replies
    • 245 views

  11. Genesis Controller/L & L Kiln -- Delay Start Question

    By NanS,
    • 2 replies
    • 202 views

  12. Should i buy Paragon TNF-273 kiln

    By Aefonty,
    • 2 replies
    • 348 views

  13. Cress kiln FX23

    By Newbietx,
    • 2 replies
    • 205 views

  14. Duncan Teachers Plus 1100 degrees after 12 hours

    By Eagleangel,   
    • 8 replies
    • 510 views

  15. Looking for a relay replacement in Melbourne

    By TaraB,   
    • 3 replies
    • 173 views

  16. Evenheat Kiln Not Getting to Temperature

    By Molly B,
    • 2 replies
    • 273 views

  17. Setting up my kiln, venting

    By Honeyhas6,
    • 7 replies
    • 453 views

  18. Kiln Ventilation advice - kiln in internal garage

    By Anna M,
    • 2 replies
    • 388 views

  19. Favorite store bought kiln wash? 1 2

    By not a bot,
    • 33 replies
    • 1.5k views

  20. wheel making loud noise (Speedball Artista)

    By ktzd_,
    • 2 replies
    • 365 views

  21. witness and sitter cone under/over firing; danbury, NH

    By suz davis,
    • 13 replies
    • 529 views

  22. Fixing up an older Brent C wheel

    By pteridonut,
    • 3 replies
    • 429 views

  23. Old Brent identity

    By Rolf,
    • 10 replies
    • 388 views

  24. Bailey double vent system vs others?

    By JRW,
    • 7 replies
    • 393 views

  25. Sheared pigtail where pigtail ends and element begins

    By Ret,
    • 5 replies
    • 157 views
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept