Jump to content

Equipment Use and Repair

Use and maintenance of kilns, wheels, pug mills, slab rollers, etc. 
Moderated by: Neil Estrick

3,278 topics in this forum

  1. Kiln proximity to propane heater or garage door

    By Heidi KH,   
    • 2 replies
    • 404 views

  2. From 4 cuft to 12 cuft, finally got a big boy kiln! 1 2 3

    By liambesaw,
    • 60 replies
    • 4.4k views

  3. Another KM1227 question

    By brettwulc,
    • 4 replies
    • 280 views

  4. Need Kiln Burner "Orifice Connector"

    By ThruTraffic,
    • 3 replies
    • 293 views

  5. Bent Bolt on clay boss tension plate

    By Im_ryan_,   
    • 3 replies
    • 331 views

  6. Gare Kiln

    By ClayCreations,   
    • 19 replies
    • 11.5k views

  7. 1227 vent holes not pulling during whole firing

    By brettwulc,
    • 3 replies
    • 264 views

  8. North star tile press

    By Noodles747,
    • 4 replies
    • 550 views

  9. Kiln taking a long time to reach temp with new elements

    By Osso,
    • 11 replies
    • 350 views

  10. My kiln keeps turning off

    By Paolaeffio,
    • 3 replies
    • 389 views

  11. Using angle grinder to remove glaze from a kiln shelf? 1 2

    By thiamant,
    • 26 replies
    • 2.6k views

  12. kiln advice top-loader vs front-loader

    By akilspots,
    • 13 replies
    • 1.5k views

  13. Looking at a used kiln and dont know what to offer

    By Darlene,
    • 1 reply
    • 199 views

  14. Alsager type wheel replacing a drivebelt

    By diddlyzip,
    • 0 replies
    • 138 views

  15. Mercury Relay Replacement Help

    By bayanMM,
    • 4 replies
    • 598 views

  16. Need help fixing the foot pedal of a Creative Industries wheel

    By spring,
    • 1 reply
    • 407 views

  17. New (to me!) kiln needs some help

    By kylies.clay,
    • 4 replies
    • 649 views

  18. Old shimpo wheel stuck in left hand mode

    By PSC,
    • 11 replies
    • 3.3k views

  19. Kiln wall/floor thickness questions

    By AaronRotchadl,
    • 3 replies
    • 590 views

  20. Element pigtail too short

    By Osso,
    • 8 replies
    • 540 views

  21. Crossdraft salt glaze

    By Mirrored-K-Studio,
    • 4 replies
    • 460 views

  22. Sitter Kiln help.

    By Readytopot,
    • 2 replies
    • 125 views

  23. My wheel head is slightly off

    By Elenajac,
    • 7 replies
    • 479 views

  24. I want to get a gas kiln that can run on propane. Which one is the best?

    By Camila PM,
    • 3 replies
    • 656 views

  25. Broken Bricks in top of Kiln Lid

    By TanyaW,
    • 5 replies
    • 396 views
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept