Jump to content

Equipment Use and Repair

Use and maintenance of kilns, wheels, pug mills, slab rollers, etc. 
Moderated by: Neil Estrick

3,282 topics in this forum

  1. Replace lid or buy new kiln

    By Vonzini,
    • 3 replies
    • 204 views

  2. Cress Et28 power button lights up but brand new control board not turning on

    By ktribble23,
    • 4 replies
    • 208 views

  3. Considerations for kiln unconditoned space

    By Singing Pond Farm,
    • 2 replies
    • 109 views

  4. Kiln problem

    By Lotna,
    • 1 reply
    • 99 views

  5. Hi! I'm new here :-) And I just bought an old kiln!

    By Naaie,
    • 1 reply
    • 105 views

  6. Vent fan for downdraft Kiln vent

    By MissyLee5,
    • 4 replies
    • 593 views

  7. Cress kiln not reaching cone 6

    By Ksmith,
    • 12 replies
    • 269 views

  8. Wiring in

    By AutumnGrace,   
    • 4 replies
    • 418 views

  9. Newbie question re kiln

    By Leelee,
    • 1 reply
    • 216 views

  10. Is there a place to buy a used slab roller & wall-mounted extruder?

    By Christy Ann,
    • 10 replies
    • 3.3k views

  11. Propane hook up for Olympic 2831 kiln

    By MFP,
    • 16 replies
    • 716 views

  12. accidentally started my bisque on high instead of low

    By Sweeney,
    • 2 replies
    • 113 views

  13. I plugged in the pottery wheel after many years the light was on and then it turned off, so I figured it was a fuse. I got a new fuse. It wasn’t the fuse. What should I check now?

    By Brent potterywheel,
    • 2 replies
    • 203 views

  14. Bailey Mini Might 16” Table Top Slab Roller

    By Elyse,   
    • 1 reply
    • 327 views

  15. Replacement brick for Gare 2327

    By davidh4976,
    • 2 replies
    • 79 views

  16. Paragon A88B question

    By TWarren,
    • 2 replies
    • 135 views

  17. New Kiln + Controller Advice Sought

    By Doppler9000,
    • 9 replies
    • 609 views

  18. cone offset or thermocouple offset l&l easyfire

    By akilpots,
    • 3 replies
    • 110 views

  19. Kiln recommendation - England

    By Vix,   
    • 6 replies
    • 212 views

  20. Did I just mess up my kiln?

    By Sadkiln,
    • 9 replies
    • 592 views

  21. Bluebird 440 Pug mill Vacuum chamber reseal

    By Chica,
    • 1 reply
    • 119 views

  22. Selling a kiln, replace the elements or not?

    By Bam2015,
    • 2 replies
    • 129 views

  23. Used old shelf primer and this happened, can you help?

    By LauraLucht,
    • 6 replies
    • 254 views

  24. Slab Roller Plans

    By AlanMalawi,   
    • 3 replies
    • 411 views

  25. Shimpo RK-5TF pottery wheel in need of a service

    By Cirillo,
    • 1 reply
    • 102 views
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept