-
Posts
11,963 -
Joined
-
Last visited
About Mark C.
- Birthday 03/15/1953
Contact Methods
-
Website URL
http://www.liscomhillpottery.com
Profile Information
-
Location
Near Arcata Ca-redwood rain forest
-
Interests
Diving-underwater photo-salvage diving-dive Travel
Extreme offshore tuna fishing off north coast of Ca.
Recent Profile Visitors
460,592 profile views
Mark C.'s Achievements
Advanced Member (3/3)
6.6k
Reputation
-
Hulk reacted to a post in a topic: Am I applying bat wash correctly?
-
Piedmont Pottery reacted to a post in a topic: slab plates center warping during glaze fire
-
Magnolia Mud Research reacted to a post in a topic: Am I applying bat wash correctly?
-
Frit Substitution Chart + Orton Cone Charts + Kiln Wash Recipes
Mark C. replied to Min's topic in Clay and Glaze Chemistry
If one is thinking about using commercial wash .I would make my own wash and remove with a wet sponge before firing any commercial wash as it usually poor quality. Speaking of quailty wash I noticed on the Advander shelve (kiln shelve.com ) site they use the same formula as I posted years ago 1/2 alumina hydrate 1/4 epk 1/4 calcined EPK or (glowmax) -
Am I applying bat wash correctly?
Mark C. replied to Edda's topic in Studio Operations and Making Work
I would make my own wash and remove with a wet sponge before firing any commercial wash as it usually poor quality. Speaking of quailty wash I noticed on the Advancer shelve (kiln shelve.com ) site they use the same formula as I posted years ago 1/2 alumina hydrate 1/4 epk 1/4 calcined EPK or (glowmax) -
Pres reacted to a post in a topic: What’s on your workbench?
-
My guess is freezing as well-one to many, but really trial and error is the only wat to know.
-
Hulk reacted to a post in a topic: What’s on your workbench?
-
Denice reacted to a post in a topic: What’s on your workbench?
-
Rae Reich reacted to a post in a topic: What’s on your workbench?
-
Firing two glaze fires today still trying to appease the pit monster.I can now work 1/2 days before foot say no more.Spent many 1/2 days glazzing and loading up till todays firing. Spring mini heat wave yesterday (81 was the high and the low was 37) it's a 3 day deal.
-
Pres reacted to a post in a topic: What’s on your workbench?
-
Troubleshooting my L & L manual Econo Kiln J230
Mark C. replied to GrayB's topic in Equipment Use and Repair
The gap looks fine and I would not cement it.Cold bottom is normal as well -
Pres reacted to a post in a topic: Price Check - Kiln, Wheel, Slab Roller
-
Rae Reich reacted to a post in a topic: QotW: What surprise have you found in your clay, either fresh or recycled?
-
Yes that nozzle is what I was speaking about-as you will need a nozzel the specks are- ITEM IS NEW, OD 12 5/8 inches ID 9 5/8 inches
-
slab plates center warping during glaze fire
Mark C. replied to chris123's topic in Studio Operations and Making Work
I make square slab plates on a plaster slump molds . they are not footed (no coils added). They pop off the plaster well and have a curve to them which lessens in the glazze fire. They have a square area that is flat in about 1/3 of the form with the lip angled up. I have to sizes and have way better luck with the smaller 8-9 inch than the larger 14-12 inch which loves to lay down to much in a glaze fire -
slab plates center warping during glaze fire
Mark C. replied to chris123's topic in Studio Operations and Making Work
For me throwing the whokle thing on the wheel is faster by far. The time is trimming a foot.The wares are solid and do not warp. The compression is good and no memory issues with the clay . -
I threw my first pots yesterday after a 8. week break. I had a tarsal tunnel surgery on right foot and out of cast now and in a boot for a month. I got off crutches and knee scooter about 4 days ago and am taking baby steps towards walking again. Going to make some small stuff this am as well. Slowly getting back to it. Lots of PT and doing my PT 3 times a day then ICE and infrared light. Compression sleeve 99% on time as well . Wound is about 5 inchs long and coming along nicely. This surgery was a real setback for 8 weeks. I have a large order to fill this spring and am just starting to get to it. I will be driving my self again within a day-ya hoo PS tarsel tunnel is just like carpel tunnel on wrist only on the foot. Both by feet have it. I shosse the worst right foot to do this year -if it gets better in 3-6 months I will conside the other one. Right now that sound really like a bad idea but once I;m healed up and if it works then I will think more about it on other foot.Surgery was a 4 hour trip away one way. Specialized doctor for this type of surgery of course.
-
I'll get those measurements tomorrow-I'll be guessing on the Id on the larger end-OD is easy
-
Just need a top and the barrel made up. There is a new peter pugger barrel on ebay now. I own that vp20 (its the same one on ebay) so I can measure that diameter for you if you go that route .
-
Mark C. reacted to a post in a topic: GT400 Laguna Pacifica pedal help
-
Pigtail broke, do I have to have a new element?
Mark C. replied to shawnhar's topic in Equipment Use and Repair
I can grind an insulator down and send it along with a clamp if needed?