kristinanoel Posted June 7, 2018 Report Share Posted June 7, 2018 Hi all, As I dive into the beauty of repetition, I find myself in need of a better way to quickly and accurately measure various dimensions while throwing and trimming. The only two tools I'm aware of are the single (or multi arm) throwing gauge and the tombo sticks, and I'm looking for your pro/con experiences with either of those, a source for purchase, or any other recommendations you might have. Thanks, Kristina Link to comment Share on other sites More sharing options...
Rex Johnson Posted June 7, 2018 Report Share Posted June 7, 2018 I know Mea and some others use a flexible gauge that connects to the wheel. I need to make one, maybe someone will chime in... Link to comment Share on other sites More sharing options...
oldlady Posted June 7, 2018 Report Share Posted June 7, 2018 a potter i know uses a light that shines down with pinpoint accuracy so he knows when the outside edge is correct. nothing in the way of his hands. Link to comment Share on other sites More sharing options...
Rex Johnson Posted June 7, 2018 Report Share Posted June 7, 2018 I like that idea. Link to comment Share on other sites More sharing options...
preeta Posted June 7, 2018 Report Share Posted June 7, 2018 Learnt from Simon Leach. A blob of clay on the rim of the splash pan. Stick in your gauge which usually is a stick. I use a brush. It’s still that point idea which give you both width and height at one point. Very accurate. Basically a throwing gauge I still prefer the red dot pointer light but haven’t rigged it up yet. Link to comment Share on other sites More sharing options...
Magnolia Mud Research Posted June 7, 2018 Report Share Posted June 7, 2018 I use wooden coffee stirrers for most measurements. Make a mark on the stick, and stick to that mark. Link to comment Share on other sites More sharing options...
GEP Posted June 7, 2018 Report Share Posted June 7, 2018 Here’s a blog post about my flexible throwing gauge, that @Rex Johnson mentioned above. Made for free from a broken gooseneck table lamp. http://www.goodelephant.com/blog/throwing-multiples-without-losing-your-mind Link to comment Share on other sites More sharing options...
Callie Beller Diesel Posted June 8, 2018 Report Share Posted June 8, 2018 I like the look of Mea's, but I don't have a broken lamp. So in terms of direct experience, I give a +1 to the stick-in-the-lump-of-clay trick, as I happened to already posess both a stick and a lump of clay. Link to comment Share on other sites More sharing options...
lbbloom Posted June 11, 2018 Report Share Posted June 11, 2018 I've just started using an adjustable gauge that I got from Euclids. Here is the link: https://www.euclids.com/index.php?item_id=TFAPG What i like about it is that it pivots so that it does not get in my way. Link to comment Share on other sites More sharing options...
Dick White Posted June 11, 2018 Report Share Posted June 11, 2018 Not to be a stick in the mud (very very bad pun, naughty boy, go to your room and don't come out until you have picked up all your toys...) but a concern with the stick (or whatever) in the blob of clay on the edge of the splash pan is that if you are going to do a long production run over a considerable length of time, the clay will begin to dry and shrink, and the pointer end of the stick will move. The movement will be imperceptible from piece to piece, but the size of the last piece of the day will not be the same as the first. If you don't mind spending a bit more than a trip you your favorite coffee shop to snitch some extra stirring stick Hsin-Chuen Lin (of UBoob video fame) markets a metal adjustable tombo gauge with measured markings and an alternate configuration of the tool to measure the thickness of the bottom of your pot before you trim (so you know exactly who deep you can trim your footring). Link to comment Share on other sites More sharing options...
Pres Posted June 11, 2018 Report Share Posted June 11, 2018 I like to use the cheap flexible straws stuck in a piece of clay when I don't have anything better for consistency. I use a pair of calipers for lids/mouths. best, Pres Link to comment Share on other sites More sharing options...
Callie Beller Diesel Posted June 11, 2018 Report Share Posted June 11, 2018 I find I get more shift from my clay bat patty flattening over a production run than I do from clay shrinkage over the course of a day. Link to comment Share on other sites More sharing options...
Sputty Posted June 11, 2018 Report Share Posted June 11, 2018 . Link to comment Share on other sites More sharing options...
hitchmss Posted June 11, 2018 Report Share Posted June 11, 2018 I use a 10" log from my pugmill wrapped in a piece of plastic held in place with rubber band. Shove long handled plastic brush in it and set to height/width. Heavy/doesn't move, doesn't dry out and shift size, easy to adjust/set, brush doesn't gouge pot rims if you get too big, hang wire tool over brush, needle tool gets shoved in top of log. Use a pair of plain old calipers to measure your floor opening and keep your weight of balls consistent=uniform pot sizes. Link to comment Share on other sites More sharing options...
oldlady Posted June 11, 2018 Report Share Posted June 11, 2018 sputty, thank you for reviving isaac button! remember seeing the videos years ago and so appropriate today when "work" seems to be a word from the past. someone must have asked him to remove the pipe so we could see his face. i think the reason he kept it in his mouth is that there is nowhere to put it that it would not get covered with clay. Link to comment Share on other sites More sharing options...
Sputty Posted June 11, 2018 Report Share Posted June 11, 2018 . Link to comment Share on other sites More sharing options...
Rae Reich Posted June 11, 2018 Report Share Posted June 11, 2018 Lovely throwing demo! Found myself holding my breath during the long first raising pass of the last big piece, then slow exhales on the shaping passes and big smile for the collar/shoulder mastery. Note: the temporary plug on the freshly thrown form keeps air inside to hold its shape for moving. Link to comment Share on other sites More sharing options...
Sputty Posted June 11, 2018 Report Share Posted June 11, 2018 . Link to comment Share on other sites More sharing options...
Callie Beller Diesel Posted June 11, 2018 Report Share Posted June 11, 2018 The technique used for lifting what are probably 30 lb wet pots off the wheel is pretty cool too. Link to comment Share on other sites More sharing options...
Sputty Posted June 11, 2018 Report Share Posted June 11, 2018 . Link to comment Share on other sites More sharing options...
preeta Posted June 12, 2018 Report Share Posted June 12, 2018 14 hours ago, Sputty said: When Button retired in the mid-60s, he had already spent nearly 20 years running the pottery on his own, unable to find anyone willing to become an apprentice. That neatly coincides with the end of the second World War, when returning servicemen were looking for 'better' things - I suppose - than slapping a ton of clay around every day for pennies. Before the war, there were a dozen or so working at Soil Hill, Button's workshop. That was true of George Orr too. He died a mechanic, not a potter. And his burnt babies sat in a box for 50 years in a museum before they were discovered. I think by accident. I forget the historical east coast family that could not even hold on to their property and had to sell it in 2015/16 I believe. Locally I have watched a local pottery factory get smaller and smaller. It makes me sad for the history we are losing... I feel it’s similar to farming. Old farmers are dying without passing on their knowledge. Yet I see new farmers come up who have to learn from scratch. I hear young potters in the age of 3D printers say why learn the wheel. Yet ceramic programs in Asian universities are growing. Its all changing and evolving!!! Link to comment Share on other sites More sharing options...
Pres Posted June 12, 2018 Report Share Posted June 12, 2018 I hope, and have believed that much of what we value as a society defines the society. It seems money is the largest factor of late, even though some folks do things for the love of doing them. There are those that have their hobbies, woodworking, ceramics, jewelry or bead craft, or even sewing. However, is going by the wayside as Preeta says. Does it take another revival as we went through in the 50-80's, for much of the interest in "hand crafted/made returns? Seems like there will be a time when time at hand is more available, as more and more of actual production becomes so automated. Will this stimulate a return to valuing things that are once again made by hand with skill and taste. Will the only folks that will appreciate this be the ones with money? I hope this is not just a dream, but know that I will not see it happen. best, Pres Link to comment Share on other sites More sharing options...
Sputty Posted June 12, 2018 Report Share Posted June 12, 2018 . Link to comment Share on other sites More sharing options...
preeta Posted June 23, 2018 Report Share Posted June 23, 2018 this is an interesting conversation here. one of the things i am discovering as my 15 shares her world history thoughts with me is that there is no 'one' society. As we talked about suffragette i suddenly realized that is the history of one part of society, not all of it. that privilege for some others still had to wait 50 years. yes one part of society is valued by money. but that makes sense doesnt it? when we have such an elitist society. perhaps if we had more of an egalitarian society money wouldnt be such a big thing. i think the world is full of non Robert Fourners, but there are always a few Robert Fourner's who do question and survive. while maybe the majority values dont match the minority value, but there are people who ARE choosing family over a better paying job. the minority does have a voice and it does exist. bottom line is we have to choose which way to go. what we want to do. there is still a choice. its these teenagers who have helped me see that. they are not falling into the buy in. even though they realize they are biased by the ads they are struggling and suffering to be true to their own beliefs. i mean today we still have handmade embroidery. we really shouldnt have since the sewing machine came out over 200 years ago. Link to comment Share on other sites More sharing options...
nancylee Posted July 3, 2018 Report Share Posted July 3, 2018 Sorry to be dense, but how does one stick stuck in a blob of clay give you height and width? A duh moment - sorry! nancy Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.