docweathers Posted February 28, 2017 Report Share Posted February 28, 2017 I had always been very diligent every time I used wax resist to quickly scrub out the resist. This kind of worked to make a brush flat last a bit longer, but slowly wax was building up in it. The other day I forgot to wash out the brush at all, a trashed brush, I thought. I found a quick way to make it come perfectly clean again. I took a small glass jar and put a little water and dish soap in the bottom. I stuck the brush in it and put it in the microwave for about 10 seconds, until the water was slightly boiling. I pull it out of the microwave, swished around in the solution. The brush was absolutely clean, like brand-new, no wax. I thought others might find this discovery useful. Link to comment Share on other sites More sharing options...
neilestrick Posted February 28, 2017 Report Share Posted February 28, 2017 Thanks for the tip! I use the wax resist from Ceramic Supply. It rinses out clean with just water, and never gums up the brushes. Link to comment Share on other sites More sharing options...
docweathers Posted February 28, 2017 Author Report Share Posted February 28, 2017 That is even a better idea.... from one of the old pros. Link to comment Share on other sites More sharing options...
Marko Posted February 28, 2017 Report Share Posted February 28, 2017 Thanks for the tip! I use the wax resist from Ceramic Supply. It rinses out clean with just water, and never gums up the brushes. What brand? Link to comment Share on other sites More sharing options...
docweathers Posted February 28, 2017 Author Report Share Posted February 28, 2017 There did not seem to be any noticeable heating of the metal even though the brush that I used had a lot more metal than most small brushes. I suspect that's because the metal is submersed in water and the microwave is only on for about 10 seconds. Link to comment Share on other sites More sharing options...
neilestrick Posted February 28, 2017 Report Share Posted February 28, 2017 Thanks for the tip! I use the wax resist from Ceramic Supply. It rinses out clean with just water, and never gums up the brushes. What brand? It's not labeled with a brand. It's just their house brand I guess. Link to comment Share on other sites More sharing options...
Chris Campbell Posted February 28, 2017 Report Share Posted February 28, 2017 In case you have to use up the stuff you already have on hand ... a trick from an old Ceramics Monthly was to gently rub some liquid soap into the brush before using it to prevent the wax from sticking in the first place. Link to comment Share on other sites More sharing options...
Callie Beller Diesel Posted March 1, 2017 Report Share Posted March 1, 2017 I was just going to suggest exactly what Chris said. I don't have access to water soluble resist, so my brush gets some Sunlight dish soap, or some ivory hand soap thoroughly worked into the bristles down to the ferrule. Helps it wash right out after your waxing session. Link to comment Share on other sites More sharing options...
Benzine Posted March 1, 2017 Report Share Posted March 1, 2017 In case you have to use up the stuff you already have on hand ... a trick from an old Ceramics Monthly was to gently rub some liquid soap into the brush before using it to prevent the wax from sticking in the first place. Yes indeed. I require my students to do this, with both wax and latex resist. Probably saves me a few dozen brushes a year. Link to comment Share on other sites More sharing options...
Marcia Selsor Posted March 2, 2017 Report Share Posted March 2, 2017 Linda Arbuckle recommended using liquid Shout applied to the brush and rinsed before using resist. I do this for latex resist and it usually works. Marcia Link to comment Share on other sites More sharing options...
Sheryl Leigh Posted March 4, 2017 Report Share Posted March 4, 2017 Makes sense. I've used boiling water to get candle wax out of glass candle holders - but I would think the metal part of a brush would cause problems in a microwave. I'm thinking boil the water first - then put the brush in it - would be a safer method. Yeah, I would forget the ferrule and have sparks going off in the mike, I just know it.... Link to comment Share on other sites More sharing options...
LeeU Posted July 3, 2017 Report Share Posted July 3, 2017 Actually a new question, but I didn't want to post a separate thread, and the issue is in the ballpark of something mentioned here; using the microwave. Is it reasonable to assume I could reconstitute the lumpy-clumpy aging wax by microwaving at 50% power for maybe 10 seconds or so without causing any problems? In this case, it's Michelman's being used on cone 6/electric. Link to comment Share on other sites More sharing options...
Apprentice_potter Posted August 11, 2020 Report Share Posted August 11, 2020 Hi I'm a newbie potter and new to this site. Thank you Docweathers for the brush tip it was really helpful. :) Link to comment Share on other sites More sharing options...
CactusPots Posted August 11, 2020 Report Share Posted August 11, 2020 It's just the hot water to clean a wax coated brush. I've been known to leave a wax brush overnight. Boiling water is 100% effective on wax. An electric tea kettle is a necessity in my studio. Hot water for throwing, mixing soda ash and cleaning wax brushes. Occasional cup of tea. The soap trick on the brush works ok for latex resist. Maybe 85%. Use cheap brush if possible. When I get chunks of latex that won't come out on a good brush, I use a wire brush to clean it. Link to comment Share on other sites More sharing options...
Mark C. Posted August 11, 2020 Report Share Posted August 11, 2020 I use a sponge to apply most wax if just covering pot /bowl bottoms-much quicker than brushing. Brushing is good for detail work. Just cut up a 3 inch round throwing sponge like a pizza and damp the triangle sponge in water and dip into wax. easy to get straught lines and is about 80% faster than brushing. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.