Jump to content
High Bridge Pottery

Home Made Kiln Controller

Recommended Posts

It has been a while since I got to dabble with electronics. Looking into automating a gas kiln. Found a ball valve + actuator that needs 0-10v signal sent for how open it is. After some googling I found this op-amp circuit for doing that exact job so set about making it.

 

gallery_23281_871_8249.jpg

 

Took me a few failed attemps (wired the 24v positive up from actuator up to my raspberry pi and killed it, same with chip) but once I made sure it was the right circuit it all works perfectly.

Realised I never posted the MAX31855 circuit so here is that one too.

 

gallery_23281_871_9973.png

 

Tested it out on the kiln today and it works a treat. Still lots more work for actually programming the thing to do sensible things.

 

gallery_23281_871_55743.jpg

 

med_gallery_23281_871_349092.jpg

Share this post


Link to post
Share on other sites
Ju00Ls    3

Nice work Joel!   I've have been too busy at work to look at my stuff but, hope to return to it shortly;   I did buy some MAX chips to compare against the AD595;  I like the pwm to voltage converter,  thanks for posting the circuits.  

Keep up the progress!
 

Share this post


Link to post
Share on other sites
Tim T    46

I've decided that doing my own kiln controller would be an interesting project, but too much of a distraction from making pots.

This was exacerbated by my (now ex) kiln controller deciding to overfire to about 1330 (in a kiln rated to 1300!). In the soak, when the elements came on, the temperature readout dropped so they stayed on till it got to the target of 1290, then cut out and the temperature readout immediately jumped up to 1330 and the kiln cooled down to 1285, then the elements came on and the temperature immediately dropped. I guess the elements were causing a voltage drop which then affected the temperature reading.

Kiln survived, though the stoneware in it started bloating as it was an oil spot glaze with a long soak, and a while until I noticed.

Anyway, I've found that the Bentrup TC507 controller does all I need and more, and a lot quicker to get in place than rolling my own. It can also be used to control a gas kiln if you have the right valves, though I just use electric. So I'm wiring it all in, including a couple of thyristors to replace the relays which should give a longer element life.

Share this post


Link to post
Share on other sites
Ju00Ls    3

Hi;   I found a bit of spare time recently so I added some code to allow the user to add new programmes to the controller;  this took me far longer than I expected, but at least that bit is complete now.

 

to be continued... ;-)

Share this post


Link to post
Share on other sites

I have been doing a bit more work with the home made kiln controller, not too much on the software side but I tried designing some PCB's in Fritzing. It was pretty easy to use but really started going slow with the 0-10v Op Amp circuit. Don't think it's set out for making complicated ones.

 

I sent the PCB's off through the fritzing website and they supplied some mock up images of the board. Now I have to wait 1-2 weeks for the boards :( I still need to find a reliable thermocouple to run along side my board to test how accurate it is, or maybe do something with cones. Not sure on that one. I know it reads temperatures but are they right...

 

gallery_23281_871_85782.png

 

gallery_23281_871_54332.png

 

gallery_23281_871_81346.png

 

gallery_23281_871_281378.png

Share this post


Link to post
Share on other sites

The boards finally arrived :D 

 

I really need a better soldering iron, mine is the cheapest you can buy. Really tough to solder in these tiny chips but I think I have managed it. Going to test it properly sometime soon.

 

gallery_23281_871_288803.jpg

 

gallery_23281_871_773800.jpg

Share this post


Link to post
Share on other sites

Getting closer to having something that works with a kiln.  Been updating the software a bit so now it resembles something usefulish. It would be interesting to have ideas on features, not that I could add them easily :lol:. Need to order a few more things then I can get it to fire and graph an electric kiln firing.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×