dolly Posted March 15, 2014 Report Share Posted March 15, 2014 I'm sculpting a parrot with earthenware clay, I've hollowed it out and fixed the high temp wire through it's body and have 2 wire running down the parrots legs for he's perch. should i make some holes in him for the air to flow through and will he be ok to fire , grown quite attached to him lol anyone got any suggestions please ... Link to comment Share on other sites More sharing options...
Babs Posted March 15, 2014 Report Share Posted March 15, 2014 The deal is, if he is absolutely dry there is no prob. with air in his interior! Dampness is the prob with firing clay. Link to comment Share on other sites More sharing options...
dolly Posted March 15, 2014 Author Report Share Posted March 15, 2014 thanks yes I will make sure he's bone dry b4 I fire him , I was just worried about the wire, but needed something to connect him to a perch when he's fired cos he's going to be pretty heavy.... Link to comment Share on other sites More sharing options...
Benzine Posted March 15, 2014 Report Share Posted March 15, 2014 An air vent will help it dry a bit faster though. Link to comment Share on other sites More sharing options...
neilestrick Posted March 15, 2014 Report Share Posted March 15, 2014 I would not trust wire to hold a sculpture in place during a firing. It will soften as it heats. You would be better off firing it on the shelf, laying on its side, held up with stilts. Link to comment Share on other sites More sharing options...
Benzine Posted March 15, 2014 Report Share Posted March 15, 2014 Good point Neil. And the good thing about Earthenware, is the metal pointed stilts can be used for the bisque and glaze firings. Link to comment Share on other sites More sharing options...
neilestrick Posted March 15, 2014 Report Share Posted March 15, 2014 Let it dry 3 times as long as you think it needs. With a closed form, it will appear dry on the outside but still be quite wet inside. This is why closed forms often blow up, not because of the trapped air. It's a good idea to do a long preheat, too. We regularly fire closed pieces in my studio without problem, but we let them dry forever and do a good preheat. Link to comment Share on other sites More sharing options...
Bob Coyle Posted March 15, 2014 Report Share Posted March 15, 2014 I would definitely put a small non obtrusive hole somewhere into the hollow portion. My paranoia about trapped moisture may be a little greater than the rest of the opinions here but why take the chance? I've blown pieces I would swear were as dry as a bone. Link to comment Share on other sites More sharing options...
neilestrick Posted March 15, 2014 Report Share Posted March 15, 2014 I would definitely put a small non obtrusive hole somewhere into the hollow portion. My paranoia about trapped moisture may be a little greater than the rest of the opinions here but why take the chance? I've blown pieces I would swear were as dry as a bone. No matter what, it was moisture that blew it up. Could be that the firing was too fast. Since the heat only penetrates from the outside on a closed form, they take a little longer to evaporate off the last remaining bit of moisture. Link to comment Share on other sites More sharing options...
Bob Coyle Posted March 15, 2014 Report Share Posted March 15, 2014 Yeah Neil, water will do it every time. I wonder though, what happens to the water released inside a closed form during the time chemically bound water is being gassed out? There must be some gassing out inside as well as outside?? Link to comment Share on other sites More sharing options...
neilestrick Posted March 15, 2014 Report Share Posted March 15, 2014 Yeah Neil, water will do it every time. I wonder though, what happens to the water released inside a closed form during the time chemically bound water is being gassed out? There must be some gassing out inside as well as outside?? Any pressure building up inside the open space in a closed form is not enough to do any damage. The walls of the pot are thick/strong enough to contain it. But when the steam forms inside the walls of the pot you don't have that thickness/strength since the water is between the clay particles. Also, by the time chemical water starts to burn out, the atmospheric water is already gone, as well as a lot of the organic/vegetative material, so you have a more porous body at that point which can handle the evaporation more easily. Link to comment Share on other sites More sharing options...
Babs Posted March 15, 2014 Report Share Posted March 15, 2014 So the wires you are speaking of are going to be fired in situ and are his legs when the piece is finished? There was a post here about that better do a search or, Tyler has written about this in a couple of posts. Link to comment Share on other sites More sharing options...
dolly Posted March 16, 2014 Author Report Share Posted March 16, 2014 I bought the wire from my pottery supplier can withstand the heat. yes I think i will drill a hole in him just to cover myself. and wait so i'm sure he's dry. then say a little prayer whilst he's being cremated or created thanks for all your replies ... Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.