mireia casanovas Posted February 27, 2023 Report Share Posted February 27, 2023 Good morning all, I am having consistent issues with Mayco SW colours; I love them but I can't seem to fire them right. I have been using them on white stoneware (firing temp 1240ºC-1300ºC). I have applied one, two and three coats for testing and fired up to 1250 slowly and with a 30 min period at the end. I have an electric Kiln (rohde ecotop) that seems to work just perfectly. I know I am doing somthing wrong but can't guess what; all my test tiles and pieces turn brown, I am not able to make the colours pop The colors on the tiles are stoned denim and lavender, and the castle is tyger's eye If anyone has any advice it would be very much appreciated, I am totally lost! thank ou all for your time, Quote Link to comment Share on other sites More sharing options...
Chilly Posted February 27, 2023 Report Share Posted February 27, 2023 Are you using cones to verify the temperature of your kiln? My guess is they are underfired. Roberta12 1 Quote Link to comment Share on other sites More sharing options...
Roberta12 Posted February 27, 2023 Report Share Posted February 27, 2023 @Chilly asked a great question. They do look underfired. On the Mayco site they do recommend a thick application. Perhaps thicker is better with these glazes? Roberta Rae Reich 1 Quote Link to comment Share on other sites More sharing options...
Bill Kielb Posted February 27, 2023 Report Share Posted February 27, 2023 If I read the Mayco literature it seems to say cone 10 performance may be noted on the bottle. Also as I go through the website and chips they seem to be noted as fired cone 6 oxidation. Cones definitely would help. A 30 minute soak at the end likely drives things to the next one or two cones higher. Check the labels on the bottle for special notes on cone 10 firing. Quote Link to comment Share on other sites More sharing options...
mireia casanovas Posted February 27, 2023 Author Report Share Posted February 27, 2023 3 hours ago, Chilly said: Are you using cones to verify the temperature of your kiln? My guess is they are underfired. Hi Chilly, thank you for your help, I did not use cones, I will next time to ensure they are not underfired. thank you Rae Reich and Chilly 2 Quote Link to comment Share on other sites More sharing options...
mireia casanovas Posted February 27, 2023 Author Report Share Posted February 27, 2023 19 minutes ago, Bill Kielb said: If I read the Mayco literature it seems to say cone 10 performance may be noted on the bottle. Also as I go through the website and chips they seem to be noted as fired cone 6 oxidation. Cones definitely would help. A 30 minute soak at the end likely drives things to the next one or two cones higher. Check the labels on the bottle for special notes on cone 10 firing. Thank you Bill, I was not aware that the soak at the end would rise the cones (I'm quite new to this), so thank you. I was firing at cone 6 so I should still be in the 6 to 10 range like Mayco recommends. I will fire with cones next time to make sure the kiln reaches the correct temperature thanks! I was getting so frustrated because everyone says the glazes are so easy to use and provide consistent results :S best regards from Spain Quote Link to comment Share on other sites More sharing options...
mireia casanovas Posted February 27, 2023 Author Report Share Posted February 27, 2023 1 hour ago, Roberta12 said: @Chilly asked a great question. They do look underfired. On the Mayco site they do recommend a thick application. Perhaps thicker is better with these glazes? Roberta Hi Roberta, I believe the thicker the better yes, probably I am using too little glaze, maybe combined with the fact that I did not use cones so I can not confirm temperature it gives me an idea of both the problems Thanks! Chilly, Roberta12 and Rae Reich 3 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.