efaucheux Posted November 9, 2012 Report Share Posted November 9, 2012 I'm firing my students work to cone 6. The elements are old and need changing but I went for it anyway. 30 hours later I shut the kiln off and it never hit temp (kilnsitter cone never melted) Am I going to have puddles of glaze on the shelves? Link to comment Share on other sites More sharing options...
Mark C. Posted November 9, 2012 Report Share Posted November 9, 2012 my guess in No. Mark Link to comment Share on other sites More sharing options...
Chris Campbell Posted November 9, 2012 Report Share Posted November 9, 2012 I agree as well ... If you never reached Cone temp nothing will be puddled. Link to comment Share on other sites More sharing options...
Guest JBaymore Posted November 9, 2012 Report Share Posted November 9, 2012 Firing is about heat work. Combo of temperature increase over time. If you were using a cone to measure the the heat work (properly installed in the sitter) and the cone never melted there then the heat work was not done to the work IN the kiln either....just like the cone in the sitter. It should be fine if they were all cone 6 glazes. best, ........................john Link to comment Share on other sites More sharing options...
Marcia Selsor Posted November 9, 2012 Report Share Posted November 9, 2012 sounds like your kiln is ready for some new elements. Marcia Link to comment Share on other sites More sharing options...
efaucheux Posted December 31, 2012 Author Report Share Posted December 31, 2012 I changed the elements and tested to make sure they are all working. Fired another cone 6 glaze fire. Again, after 30 hours the cone in the kiln sitter never melted. The glow from the kiln never got beyond orange. I need a pyrometers I guess. Around 30 hrs I shut the kiln off. Over 1/2 the pots were glossy but the others were Still chalky looking. Obviously not hitting temp. I guess I need to get an electrician to come Check out the kiln. Glazes were amaco potters choice glazes. Think I can re-fire? Link to comment Share on other sites More sharing options...
Mark C. Posted December 31, 2012 Report Share Posted December 31, 2012 I think its not the elements then. Maybe kiln or supply voltage is different. Need more info . Yes you can refire them Mark Link to comment Share on other sites More sharing options...
Lucille Oka Posted December 31, 2012 Report Share Posted December 31, 2012 Have you adjusted the fall weight on the Sitter? Do you use self-supporting or large pyrometric cones in the kiln so you can get an idea of what's going on in there? Have you applied a small amount of kiln wash to the little bars which hold the cone on the Sitter? How big is your kiln? 30 hours seems like a long time to fire unless you are doing a wood firing in a huge kiln. Have you talked to the kiln manufacturer yet? Amaco states that the temperature for PCs is cone 5-6, (2205-2269 degrees F). If some of the pieces are glossy and some are not where were the pieces that are glossy located in the kiln. Could this possibly be a zone fire kiln? Link to comment Share on other sites More sharing options...
Marcia Selsor Posted December 31, 2012 Report Share Posted December 31, 2012 It could also be the switches. Or a connection. Has this old kiln been on the same wiring for a long time? Do you know if the voltage, as Mark suggests, is correct. Have an electrician check the current with an ammeter to see if everything is working. The electrician should be able to pinpoint where there is a problem. Marcia Link to comment Share on other sites More sharing options...
yedrow Posted January 1, 2013 Report Share Posted January 1, 2013 Last month I had a similar problem. I had a fuse blow, a relay go bad, and a blade on the female plug burn up. All three caused the same problem. You may want to check if you are getting current to the right place. It's possible you didn't get the elements wired well and you are looking at a new problem that looks exactly like the old problem. Also, you may want to look at the plug and see if it's gotten hot. The screws that hold the wires in can work their way out and create resistance that increases heat that burns away material that increases resistance that creates more heat, and so on. I would first turn the kiln on while it is empty and watch through the spy holes to see if the elements get red, or touch the energized elements with some tissue to see if it burns. Joel. Link to comment Share on other sites More sharing options...
Mark C. Posted January 1, 2013 Report Share Posted January 1, 2013 Last month I had a similar problem. I had a fuse blow, a relay go bad, and a blade on the female plug burn up. All three caused the same problem. You may want to check if you are getting current to the right place. It's possible you didn't get the elements wired well and you are looking at a new problem that looks exactly like the old problem. Also, you may want to look at the plug and see if it's gotten hot. The screws that hold the wires in can work their way out and create resistance that increases heat that burns away material that increases resistance that creates more heat, and so on. I would first turn the kiln on while it is empty and watch through the spy holes to see if the elements get red, or touch the energized elements with some tissue to see if it burns. Joel. I gave up on plugs for this reason above a long time ago and hardwired all my electrics. Never had a plug issue since. On this note Yedrow mentions the screws-clean your wire connections and coat with an oxidation prohibitor and retighten them down. Mark Link to comment Share on other sites More sharing options...
yedrow Posted January 1, 2013 Report Share Posted January 1, 2013 I think I'm going to do exactly that Mark. I'm going to put a breaker inline and hardwire the thing so I can throw a switch instead of unplugging it. Joel. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.