Pompots Posted April 16, 2013 Report Share Posted April 16, 2013 I started to throw a pot and it collapsed on me, I really like the way it looks this way and i have plans for it, the bottom still really thick, so I need to trim some out, my question is How do I trim this, I dont have a Chuck big enough for it, any ideas? Thanks, and may the clay Gods be with you. Link to comment Share on other sites More sharing options...
Chris Campbell Posted April 16, 2013 Report Share Posted April 16, 2013 It is easy to throw a chuck big enough ... you don't have to fire it or take it off the wheel ... just let it harden enough to support your form and make sure your other piece's bottom stays moist enough to trim. Link to comment Share on other sites More sharing options...
Biglou13 Posted April 16, 2013 Report Share Posted April 16, 2013 Keep pot moist . Make a bigger chuck. Prolly not what you wanted to hear. Link to comment Share on other sites More sharing options...
OffCenter Posted April 16, 2013 Report Share Posted April 16, 2013 I started to throw a pot and it collapsed on me, I really like the way it looks this way and i have plans for it, the bottom still really thick, so I need to trim some out, my question is How do I trim this, I dont have a Chuck big enough for it, any ideas? Thanks, and may the clay Gods be with you. Throw a chuck like Chris said but don't wait for it to harden. Instead put plastic wrap over the wet clay. The wet clay is easy to mold around the piece being trimmed and when done it's ready to be wedged up. Jim Link to comment Share on other sites More sharing options...
Chris Campbell Posted April 16, 2013 Report Share Posted April 16, 2013 I started to throw a pot and it collapsed on me, I really like the way it looks this way and i have plans for it, the bottom still really thick, so I need to trim some out, my question is How do I trim this, I dont have a Chuck big enough for it, any ideas? Thanks, and may the clay Gods be with you. Throw a chuck like Chris said but don't wait for it to harden. Instead put plastic wrap over the wet clay. The wet clay is easy to mold around the piece being trimmed and when done it's ready to be wedged up. Jim Brilliant!! Link to comment Share on other sites More sharing options...
mregecko Posted April 16, 2013 Report Share Posted April 16, 2013 I started to throw a pot and it collapsed on me, I really like the way it looks this way and i have plans for it, the bottom still really thick, so I need to trim some out, my question is How do I trim this, I dont have a Chuck big enough for it, any ideas? Thanks, and may the clay Gods be with you. I actually trim things upright pretty often... Especially when I don't have the right-sized chuck and don't want to use a ton of clay to make one. You need a non-absorbant bat, and just a little bit of water on the bat (I usually just wipe it with a sopping sponge). Level the bottom of the pot as much as you can, and then (with both hands) rub it in small circles on the bat+water. A lot of people use this technique to smooth out / level the bottom of pots. If you keep at it, there will be a point where the clay absorbs most of the water and adheres to the bat. It will become VERY hard to move, but you can still do small adjustments to center it. I trim it upright like this, and then do any finishing on the bottom by hand... Carving out any extra clay on the bottom by hand with foam and a banding wheel. Link to comment Share on other sites More sharing options...
Pompots Posted April 17, 2013 Author Report Share Posted April 17, 2013 Thanks Everyone for your input, both are great ideas, Thanks a lot for your help. I think i might try the upright trimming sounds like the fastest way since the clay is at the right time to trim. You all are awesome and may the clay Gods be with you. Pompeyo. Link to comment Share on other sites More sharing options...
Pompots Posted April 17, 2013 Author Report Share Posted April 17, 2013 I started to throw a pot and it collapsed on me, I really like the way it looks this way and i have plans for it, the bottom still really thick, so I need to trim some out, my question is How do I trim this, I dont have a Chuck big enough for it, any ideas? Thanks, and may the clay Gods be with you. I actually trim things upright pretty often... Especially when I don't have the right-sized chuck and don't want to use a ton of clay to make one. You need a non-absorbant bat, and just a little bit of water on the bat (I usually just wipe it with a sopping sponge). Level the bottom of the pot as much as you can, and then (with both hands) rub it in small circles on the bat+water. A lot of people use this technique to smooth out / level the bottom of pots. If you keep at it, there will be a point where the clay absorbs most of the water and adheres to the bat. It will become VERY hard to move, but you can still do small adjustments to center it. I trim it upright like this, and then do any finishing on the bottom by hand... Carving out any extra clay on the bottom by hand with foam and a banding wheel. This option worked out perfectly for me, thanks a lot. I stuck the pot directly onto the wheel head and it worked like a charm. Link to comment Share on other sites More sharing options...
mregecko Posted April 17, 2013 Report Share Posted April 17, 2013 I started to throw a pot and it collapsed on me, I really like the way it looks this way and i have plans for it, the bottom still really thick, so I need to trim some out, my question is How do I trim this, I dont have a Chuck big enough for it, any ideas? Thanks, and may the clay Gods be with you. I actually trim things upright pretty often... Especially when I don't have the right-sized chuck and don't want to use a ton of clay to make one. You need a non-absorbant bat, and just a little bit of water on the bat (I usually just wipe it with a sopping sponge). Level the bottom of the pot as much as you can, and then (with both hands) rub it in small circles on the bat+water. A lot of people use this technique to smooth out / level the bottom of pots. If you keep at it, there will be a point where the clay absorbs most of the water and adheres to the bat. It will become VERY hard to move, but you can still do small adjustments to center it. I trim it upright like this, and then do any finishing on the bottom by hand... Carving out any extra clay on the bottom by hand with foam and a banding wheel. This option worked out perfectly for me, thanks a lot. I stuck the pot directly onto the wheel head and it worked like a charm. So glad to hear :-) Happy potting! Link to comment Share on other sites More sharing options...
Rebekah Krieger Posted April 17, 2013 Report Share Posted April 17, 2013 I started to throw a pot and it collapsed on me, I really like the way it looks this way and i have plans for it, the bottom still really thick, so I need to trim some out, my question is How do I trim this, I dont have a Chuck big enough for it, any ideas? Thanks, and may the clay Gods be with you. Throw a chuck like Chris said but don't wait for it to harden. Instead put plastic wrap over the wet clay. The wet clay is easy to mold around the piece being trimmed and when done it's ready to be wedged up. Jim I like you more and more every time you post. This is a wonderful idea! Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.