wildfire Posted November 19, 2012 Report Share Posted November 19, 2012 I'm a beginning potter without much experience in glazing and glaze firing. I'm using a ^4-6 clay and ^6 glazes. I'm in the process of making flat Christmas ornaments and am wondering how to keep the glaze from dripping onto the kiln shelves. Tried stilts -- discovered that won't work when firing ^6. Have heard of wadding -- will that work in an electric kiln? What would happen if I formed wads made from the same clay as my pots (without adding the other wadding ingredients), bisque fired (or not?) and just sat the pots on those? Is there some other method I should use? Link to comment Share on other sites More sharing options...
Edith Marie Posted November 19, 2012 Report Share Posted November 19, 2012 I'm a beginning potter without much experience in glazing and glaze firing. I'm using a ^4-6 clay and ^6 glazes. I'm in the process of making flat Christmas ornaments and am wondering how to keep the glaze from dripping onto the kiln shelves. Tried stilts -- discovered that won't work when firing ^6. Have heard of wadding -- will that work in an electric kiln? What would happen if I formed wads made from the same clay as my pots (without adding the other wadding ingredients), bisque fired (or not?) and just sat the pots on those? Is there some other method I should use? Wading will work, I have not tried using just clay, suppose if you bisque the clay then set the glazed pot on if might work, experiment first…Wading is my first and only choice. Edie. Link to comment Share on other sites More sharing options...
Mark C. Posted November 19, 2012 Report Share Posted November 19, 2012 I suggest you add some alumina to the clay-just wedge it in. You would not need much. You could also use silica if you had no alumina.Alumina will resist glaze somewhat better I feel. Our salt wadding is epk and alumina it does not stick . Mark Link to comment Share on other sites More sharing options...
wildfire Posted November 19, 2012 Author Report Share Posted November 19, 2012 I suggest you add some alumina to the clay-just wedge it in. You would not need much. You could also use silica if you had no alumina.Alumina will resist glaze somewhat better I feel. Our salt wadding is epk and alumina it does not stick . Mark Thanks, Mark. Do I bisque fire before use or just stick them on? I've also read about attaching wads w/ hot glue or Elmer's school glue - really? Link to comment Share on other sites More sharing options...
wildfire Posted November 19, 2012 Author Report Share Posted November 19, 2012 I'm a beginning potter without much experience in glazing and glaze firing. I'm using a ^4-6 clay and ^6 glazes. I'm in the process of making flat Christmas ornaments and am wondering how to keep the glaze from dripping onto the kiln shelves. Tried stilts -- discovered that won't work when firing ^6. Have heard of wadding -- will that work in an electric kiln? What would happen if I formed wads made from the same clay as my pots (without adding the other wadding ingredients), bisque fired (or not?) and just sat the pots on those? Is there some other method I should use? Wading will work, I have not tried using just clay, suppose if you bisque the clay then set the glazed pot on if might work, experiment first…Wading is my first and only choice. Edie. Thanks, Edie! Link to comment Share on other sites More sharing options...
Mark C. Posted November 19, 2012 Report Share Posted November 19, 2012 No they do not need bisquing first just make them small say 1/4 inch and fire a tad slow at 1st. Roll them in palm of hand into small balls. When putting pot on shelve push a bit down to level it. Mark Link to comment Share on other sites More sharing options...
perkolator Posted November 19, 2012 Report Share Posted November 19, 2012 wadding we use is equal parts: silica, kaolin, and grog - works great! you could easily put alumina in there in place of some of the silica. Link to comment Share on other sites More sharing options...
johnnieclay Posted November 20, 2012 Report Share Posted November 20, 2012 I'm a beginning potter without much experience in glazing and glaze firing. I'm using a ^4-6 clay and ^6 glazes. I'm in the process of making flat Christmas ornaments and am wondering how to keep the glaze from dripping onto the kiln shelves. Tried stilts -- discovered that won't work when firing ^6. Have heard of wadding -- will that work in an electric kiln? What would happen if I formed wads made from the same clay as my pots (without adding the other wadding ingredients), bisque fired (or not?) and just sat the pots on those? Is there some other method I should use? wildfire-i make and use wadding made from fireclay, sand, and wood dust in equal amounts. add water until right consistency. you can sustitute good 'ol uncooked grits in place of the wood dust for a more meaningful southern experience. fire up to cone 10 - no proble. oh yeah, i do this in an electric kiln, many many times. Link to comment Share on other sites More sharing options...
Marcia Selsor Posted November 21, 2012 Report Share Posted November 21, 2012 It helps if you use glue , like Elmers glue to attach the wads to your pieces. It keeps the wads from getting loose in the kiln and rolling into other pots. Marcia Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.