Girl on Fire Posted February 24 Report Share Posted February 24 (edited) This is in regards to the very first firing of a brand new kiln. I have read posts here and elsewhere and I know @neilestrick recommends a a slow bisque to cone 5 with a 3 hour preheat but I saw a very recent video from L&L instructing to program a glaze fire at medium speed to 04 with a 1 hour preheat. https://hotkilns.com/support/pottery-kiln-videos-links/first-firing-ll-kiln-genesis-control There is also a video that shows firing a new L&L Glaze to Cone 5 at Medium Speed https://www.clayshare.com/firing-your-l-l-kiln-for-the-first-time/videos/gf11-01 So what is it? lol. I have an Easy Fire 23-S... As an aside, I have put 2 coats of kiln wash on the shelves and plan to put the third after the first fire. This was recommended somewhere... Anything wrong with this? Thanks! Edited February 24 by Girl on Fire Quote Link to comment Share on other sites More sharing options...
Bill Kielb Posted February 24 Report Share Posted February 24 (edited) 2 hours ago, Girl on Fire said: I saw a very recent video from L&L instructing to program a glaze fire at medium speed to 04 with a 1 hour preheat. https://hotkilns.com/support/pottery-kiln-videos-links/first-firing-ll-kiln-genesis-control This video appears to be about a “break in firing” or first firing with a new kiln. My thought: Maybe good to post what are you intending to fire (bisque / glaze) what cone you are firing to, any other info, like it’s heavy sculpture work not fully dry or It’s already bisqued ordinary thickness mugs etc….. to avoid confusion. Edited February 24 by Bill Kielb Quote Link to comment Share on other sites More sharing options...
Girl on Fire Posted February 24 Author Report Share Posted February 24 5 minutes ago, Bill Kielb said: This video appears to be about a “break in firing” or first firing with a new kiln. My thought: Maybe good to post what are you intending to fire (bisque / glaze) what cone you are firing to, any other info, like it’s heavy sculpture work not fully dry or It’s already bisqued ordinary thickness mugs etc….. to avoid confusion. It would be the very first firing of a new kiln. Quote Link to comment Share on other sites More sharing options...
Bill Kielb Posted February 24 Report Share Posted February 24 (edited) I think either is fine for a first time break in firing. I don’t have clayshare so I can’t speak to that video. The 04 firing in the first video is a nice soft test fire often used to season new elements. You can always practice a glaze firing later. Edited February 24 by Bill Kielb Quote Link to comment Share on other sites More sharing options...
Dick White Posted February 24 Report Share Posted February 24 There is some conflicting information about the first firing floating around, both from different kiln manufacturers, for different purposes, and even within the same manufacturer's instructions. L&L's printed manual has long instructed owners of their new kiln to do an initial break-in firing of the empty kiln (but with the furniture) slow bisque to cone 5 (yes, five, not oh-five) with a 3 hour preheat for the dual purpose of seasoning the elements to develop a protective oxide coating and to set the cement used during manufacturing to hold the kiln bricks together. Their newest manual indicates these instructions are for both the Dynatrol and Genesis controllers. Conventional wisdom by some other kiln manufacturers instruct owners of their new kilns to do the initial firing slow to 04. This is consistent with the recommendation from the manufacturer of the Kanthal elements for seasoning newly installed replacement elements, again to develop a protective oxide coating on the wire. Out on the interwebs, many commenters who own these other brands of kiln will adamantly (but incorrectly) assert that new owners of all brands of kilns should do the initial firing to 04. And now we have this new video from L&L for programming the first firing on a Genesis controller that instructs a glaze firing to 04 with a 1 hour preheat. However, if one looks around on the L&L website, there is another video for programming the older Dynatrol controller for the first firing that is consistent with the printed instructions, i.e., slow bisque to 5. Is the basic kiln constructed differently for a Genesis vs. Dynatrol controller that it would need a different initial firing? I don't work there, so don't take my word for it, but the conflict seems fishy to me. With 3 instruction sources to choose from (the printed manual and 2 videos), I would go with the 2 that are consistent, i.e, the printed manual and the Dynatrol video. But maybe that's just because I am a recovering accountant... PeterH, Hyn Patty, Callie Beller Diesel and 2 others 5 Quote Link to comment Share on other sites More sharing options...
Hyn Patty Posted February 24 Report Share Posted February 24 I second all of what D said above. While the details may vary it all has to do with properly oxidizing the new elements, whether it is a brand new kiln or simply an element replacement. In the case of a new kiln it is also about making sure all the kiln body itself is properly seated and set. People used to think you needed to fire higher than cone 04 but I think the more up to date concensus is that cone 04 is the new standard most people go by. Congrats on your new kiln! Callie Beller Diesel 1 Quote Link to comment Share on other sites More sharing options...
Girl on Fire Posted February 24 Author Report Share Posted February 24 1 hour ago, Hyn Patty said: I second all of what D said above. While the details may vary it all has to do with properly oxidizing the new elements, whether it is a brand new kiln or simply an element replacement. In the case of a new kiln it is also about making sure all the kiln body itself is properly seated and set. People used to think you needed to fire higher than cone 04 but I think the more up to date concensus is that cone 04 is the new standard most people go by. Congrats on your new kiln! Why does L&L include 2 ^5 witness cones with new kilns if their latest video shows firing to 04 for the first firing? Still confused lol Quote Link to comment Share on other sites More sharing options...
Hyn Patty Posted February 25 Report Share Posted February 25 Personally I have no idea why L&L does whatever it does. I don't own that kind of kiln. But for the most part no matter what brand of kiln you use, if it's electric, they all work about the same with only minor variations like manual versus electronic. If in doubt just call L&L up on the phone and ask them. Quote Link to comment Share on other sites More sharing options...
neilestrick Posted February 25 Report Share Posted February 25 L&L just recently changed their recommended first firing schedule from cone 5 to cone 04. Either will work fine. 23 hours ago, Girl on Fire said: Why does L&L include 2 ^5 witness cones with new kilns if their latest video shows firing to 04 for the first firing? Probably because they still have a bunch of cone 5's to use up. Use them when you do your first glaze firing. I'll talk to them about getting some 04's instead. Personally, I would do an empty glaze firing (just shelves) with the 5's because if your glaze firing is running hot or cold you can ruin a lot of work. Callie Beller Diesel and Pres 2 Quote Link to comment Share on other sites More sharing options...
Girl on Fire Posted February 25 Author Report Share Posted February 25 (edited) 24 minutes ago, neilestrick said: L&L just recently changed their recommended first firing schedule from cone 5 to cone 04. Either will work fine. Probably because they still have a bunch of cone 5's to use up. Use them when you do your first glaze firing. I'll talk to them about getting some 04's instead. Personally, I would do an empty glaze firing (just shelves) with the 5's because if your glaze firing is running hot or cold you can ruin a lot of work. Should I run an empty glaze fire after the first firing? What speed do you recommend? Edited February 25 by Girl on Fire Quote Link to comment Share on other sites More sharing options...
neilestrick Posted February 25 Report Share Posted February 25 37 minutes ago, Girl on Fire said: Should I run an empty glaze fire after the first firing? What speed do you recommend? You can just run the empty glaze as the first firing. Medium-Slow with a 1 hour preheat. Pres 1 Quote Link to comment Share on other sites More sharing options...
Min Posted February 25 Report Share Posted February 25 (edited) From the Kanthal website, they recommend an oxidation firing to 1050C / 1922F for 7 to 10 hours. I'm thinking the people who hold for 7 to 10 hours are going to be few and far between if they mean a hold at 1922F and not a slow rise up to this temp. I typically hold for 3 when replacing elements. I don't know anybody who does a re-oxidation of the heating elements. I guess they are talking about a repeat empty kiln firing? edit: Euclids recommends holding for "several" hours also. "To protect elements used under these conditions there is an element conditioning process that is desirable for FeCrAl elements, which requires heating the elements, in air, above 1830oF/1000oC, and holding for several hours. This develops an aluminum oxide coating on the outer element surface, which can dramatically improve element life.https://www.kanthal.com/en/knowledge-hub/heating-material-knowledge/operating-life-and-maximum-permissible-temperature/ "In such cases Kanthal® alloys are recommended, provided the heating elements are pre-oxidized in air at 1050°C for 7–10 hours. Reoxidation of the heating elements should be carried out at regular intervals." Edited February 25 by Min added another link Callie Beller Diesel 1 Quote Link to comment Share on other sites More sharing options...
Girl on Fire Posted February 27 Author Report Share Posted February 27 (edited) On 2/25/2024 at 10:55 AM, neilestrick said: You can just run the empty glaze as the first firing. Medium-Slow with a 1 hour preheat. I ran the first firing Glaze cone 5 medium slow with 1 hour preheat. It took 13.20 hours to complete. Does this include the 1 hour preheat? The ^5 witness cones I put on the bottom and top shelf seemed to overfire a bit. Should I add an offset when I do an actual glaze fire at cone 5? (Bottom cone is on the left) L&L E23S-3 with Genesis controller) Edited February 27 by Girl on Fire Quote Link to comment Share on other sites More sharing options...
neilestrick Posted February 28 Report Share Posted February 28 1 hour ago, Girl on Fire said: It took 13.20 hours to complete. Does this include the 1 hour preheat? Yes. And the 1 hour preheat actually takes about 3 hours because it takes about 2 hours to get to the preheat temperature before it starts the preheat time. Try a cone offset of about -15 degrees for starters. You're not over by much. Pres 1 Quote Link to comment Share on other sites More sharing options...
Bill Kielb Posted February 28 Report Share Posted February 28 5 hours ago, Girl on Fire said: The ^5 witness cones I put on the bottom and top shelf seemed to overfire a bit. Those are really really close. For the self supporting cones I would not embed them in a little wad of clay. It actually raises the surface making the tip touch just a bit sooner than expected and it can also make it difficult to set the cone evenly on its base changing the natural design angle just a bit. Quote Link to comment Share on other sites More sharing options...
Girl on Fire Posted February 28 Author Report Share Posted February 28 19 minutes ago, Bill Kielb said: Those are really really close. For the self supporting cones I would not embed them in a little wad of clay. It actually raises the surface making the tip touch just a bit sooner than expected and it can also make it difficult to set the cone evenly on its base changing the natural design angle just a bit. That makes sense. I was overly cautious about the cone sticking to the shelf. Noobie move, I know. I have kiln wash on the shelves. Do I need to worry about the cone sticking? Should I not offset the cone? Quote Link to comment Share on other sites More sharing options...
Bill Kielb Posted February 28 Report Share Posted February 28 (edited) 7 hours ago, Girl on Fire said: I have kiln wash on the shelves. Do I need to worry about the cone sticking? Should I not offset the cone? Cones ought not stick especially if your shelves are kiln washed. Cones are made of glaze, generally they will not fully melt and liquify until they are fired approximately four to six cones higher than their rating. So a cone 4 cone ground up would melt at about cone 10 pretty nicely. That’s a pretty large oops of an over firing so it’s pretty hard for them to seriously stick. For self supporting cones the bottom should be flat and reasonably level as the angle they are made and gravity ensures they bend at their calibration. Offsetting them so they do not collide with one another in a cone pack is normal. For self supporting, just try and make sure they are placed flat and level as practical. If you are worried roll out a smooth small cookie or waster slab that is flat for them to sit on and same elevation at base and tip. The guidance I always used is below. Notice there are only one to two degrees difference between 4:00 and 6:00. Pretty perfect has a range to it that happens quickly as the cone bends past 90 degrees. Edited February 28 by Bill Kielb Quote Link to comment Share on other sites More sharing options...
GEP Posted February 28 Report Share Posted February 28 In my experience, self-supporting cones can stick to the shelf if you overfire them just a little. They’re not supposed to, but it happens! As @Bill Kielb said, if you kiln wash your shelves, this is not a problem. I do not kiln wash my shelves, so I have had to chisel off some stuck cone bits. My solution to this is to use cone plaques, the kind that have holes in one side for holding non-self-supporting cones at the correct angle. I use the underside that doesn’t have holes, put kiln wash on that surface, and place my self-supporting cones on them. Any small piece of old or broken kiln furniture will work too. Roberta12, neilestrick, Bill Kielb and 1 other 4 Quote Link to comment Share on other sites More sharing options...
PotteryPam Posted September 18 Report Share Posted September 18 (edited) Related to this topic, I just did my first bisque 04 and cone six glaze firing in my new L&L e23M -3. During the bisque firing myself supporting cone fell over and fused to a pot next to it. It fell sideways, not a normal bending. Then in my glaze fine, which was done at medium speed it way over fired, my 5, 6 and 7 cones all melted down horizontally. I was overcautious and put nearly all of my pieces on cookies, and the unglazed bottoms actually stuck to the cookies! Is that because the kiln was firing way too hot? I also got minute pinholes in practically every piece. When I called the store where I had purchased the kiln they suggested that I fired to cone five with a 20 minute hold. And the other suggestions? Edited September 18 by PotteryPam Punctuation Quote Link to comment Share on other sites More sharing options...
Hulk Posted September 18 Report Share Posted September 18 Hi PotteryPam, Welcome to the Forum! Are you using an Easy-Fire program? Is cone 6 the target? Your guard (the 7) cone all the way flat, likely that's more than a full cone over. If so, dialing down a full cone might be a good place to start. My own experience - and several others who have transitioned from an older/manual kiln to a new 3" brick numerically controlled kiln - was over fire. Over fired clay can be sticky and generate glaze faults, yes. Quote Link to comment Share on other sites More sharing options...
PotteryPam Posted September 18 Report Share Posted September 18 Yes, I was using the novice program for the cone six glaze at medium speed. Perhaps I should use the fast speed which would produce less heat work, but then I’d be worried about getting other problems from going too fast? I do have the vent sure system, and I turn the vent off as soon as, the firing is done. I do not leave the vent on during cooling. Quote Link to comment Share on other sites More sharing options...
Denice Posted September 18 Report Share Posted September 18 I have had my L&L for a year, I bought boxes of the large cones for the 04, 5,6 range and tested bottom, middle and top. It was about a half cone off so I did the adjusting on the controller and ran another test firing. Still having great firings but I sure have a lot to cones, during Covid I couldn't find any. Denice Quote Link to comment Share on other sites More sharing options...
Bill Kielb Posted September 18 Report Share Posted September 18 (edited) 5 hours ago, PotteryPam said: Yes, I was using the novice program for the cone six glaze at medium speed. Perhaps I should use the fast speed which would produce less heat work, but then I’d be worried about getting other problems from going too fast? Just a few observations that may help: The cone fire programs are not.necessarily novice, they likely have performed hundreds of thousands of firings successfully - every day.. High speed, Medium Speed, Slow speed cone fire programs provide very much the same heatwork. So slower but cooler ending temp = faster but warmer ending temp with respect to heatwork. Cones are a reasonably accurate way to indicate how much heatwork was done - one of the very few ways to know accurately. Cones are made of glaze, so they reflect truly the maturity of the firing or the heatwork supplied during the firing Firing fast can be more uneven than firing slow and medium 8 hours ago, PotteryPam said: During the bisque firing myself supporting cone fell over and fused to a pot next to it. It fell sideways, not a normal because During a bisque firing generally things are sintered so melting firmly to something would be unusual or it was fired hotter than 04 Cones 5,6,7 melting indicate how much heatwork actually took place. Any chance these are actually 05,06,07 ? Things melted to the cookies likely means at least cone 6, automatic controllers generally would not have such a giant error - anything added to the program such as a long hold? Edited September 18 by Bill Kielb Quote Link to comment Share on other sites More sharing options...
PotteryPam Posted September 20 Report Share Posted September 20 I did not add anything to the programmed Cone 6 medium speed. My cones were 5,6, and 7; I used an 04 cone for my first bisque fire to 04. L and L support suggests that I fire to cone 5 instead of cone 6 next time, but I was hoping for a more accurate solution. To me that sounds like just shooting in the dark, but perhaps that’s all we can do in ceramic firings? I was thinking that it would be more accurate to try a thermocouple offset of about 100 degrees F, but I guess I’ll just try the novice Cone 5 medium speed program. Quote Link to comment Share on other sites More sharing options...
Bill Kielb Posted September 20 Report Share Posted September 20 3 hours ago, PotteryPam said: I did not add anything to the programmed Cone 6 medium speed. My cones were 5,6, and 7; I used an 04 cone for my first bisque fire to 04 No worries, good to know nothing was added. Can you post pictures of the over fired cones? I think being off by more than a cone is fairly rare. Not impossible, just not common. The cone fire mode is tested and actually try’s to follow the basis of the Orton charts. So easy to use but very capable at adjusting for loading, rates and zoning. Just didn’t want you to think it was not and also wanted to be sure the intent of whatever speed is picked is to to produce the same heat work, so firing faster should not reduce the heat work in cone fire mode. The computer will vary the ending segment rate and finish temperature to try and achieve the cone picked regardless of speed. Anyway - if you can post a picture of the cones and even the finish fired wares it may lead to other questions Roberta12 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.