Jump to content

Johnmicheal

Members
  • Content Count

    69
  • Joined

  • Last visited

About Johnmicheal

  • Rank
    Advanced Member

Profile Information

  • Location
    Mentone,Al

Contact Methods

  • Yahoo
    Nightingalepottery@yahoo.com

Recent Profile Visitors

818 profile views
  1. From an earlier post, these are the bearings I used to rebuild my RK There are the 3 different sizes: Kit9705 6204-2NSE Nachi Bearing 20x47x14:Sealed:C3:Japan Kit9706 6205-2NSE Nachi Bearing 25x52x15:Sealed:C3:Japan Kit9703 6202-2NSE Nachi Bearing 15x35x11:Sealed:C3:Japan
  2. Heat it, the aluminum head will expand better than the steel shaft. I've done it before, about to do it again, lol. Even with a healthy coat of antiseize applied it still seized.
  3. There is adjustment under the wheel, it would be a good idea to look under there to see if anything is binding. I've used, and at times had to adjust it alittle over the years. I also drilled my wheel head as stated before. Works great.
  4. It's a matter of preference, we have 4 wheels, one of them happens to be a VL lite. Unfortunately, unless you get to try your wheel out at another studio for an extended time, it's hard to say what you will like. I can say the lite is used alot at studios teaching, there are a ton of brents in schools, old shipos from the 70s still lurking about. If you're worried about not being able to throw big, 10-20 lb is pretty big. I tend to adjust my throwing to the wheels strengths, as well as my clay body. Unfortunately, the stats published by manufacturers, due little too clear this up, and we all h
  5. So instead of the multiple connectors, I could just lug the two wires and the element together?
  6. How long do you run a pugmill before you can pug out the material, say 5 gal of broken down clay.
  7. I don't disagree with the need for ventilation and I view a cone pack through the same peep, but I doubt I would ever use 6. The cone pack at the bottom, I leave till I unload, it tells me what I need to know. Does anyone have any info as to why there are so many peep holes.
  8. Box works well, I left the top and bottom open. I'm not prone to setting things where they would drop in there, and I feel better when I can see what is going on in there. In it's next upgrade, I'll probably add some more ventilation, add the other feeder wire, separating the zones, and adding the additional thermocouples for zone control. Maybe sheath the feeder wires, I like the flexible conduit and the fact it's a good ground source. We'll see, I've got to go back to makin pots.
  9. I grounded the cover, which was attached to all three sections, and wrapped the feed wires till they were clear of the cover.
  10. My feed wires and jumped wire connection. Wrapped the wire going to the controller.
  11. So obviously we need peep holes from time to time, but why are there so many, and when I'm doing brick repair, can I just get rid of some of them. I leave my top peep open, I like to see a cone drop. But the rest are kind of a waste, and when I break one with my shin, I'm wondering A. Why don't I be alittle more careful B. Why can't I plug that hole with something that doesn't protrude into the path of a shin, thigh, hip. Please avail me of thy kiln wisdom.
  12. I still love my drycleaner bags, I can't remember the last time I actually drycleaned anything, but it didn't keep me from stopping in one and asking if they had any discards. I'm still using them, and that was 5-7 years ago, with a bag of them still in storage lol. They are light, they drape well, I double, sometimes triple them up to control drying.....and sticking with the subject, my workbench is clear, I'm ready to start again, pitchers are the need for this week
  13. I love the bowl idea, and I am going file them at the bisque stage, I've got four to mess with.
  14. Third try, I'll see how it pours when it's done, lol
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.