Wyndham Posted April 7, 2015 Report Share Posted April 7, 2015 I've replaced the switches on my brent C wheels before and adjusted the Hi/Low pot setting with no trouble but this switch is giving me grief. The pedal won't start the wheel at the low pot setting no matter how adjust it. The hi pot kicks in as it should but no transition from slow to hi. Hope someone might have a thought. I've got an email into tech support but it's after hrs now, just frustrated.Thanks Wyndham Link to comment Share on other sites More sharing options...
Mark C. Posted April 7, 2015 Report Share Posted April 7, 2015 I hate to tell you this but its one on these two -a new curcuit board in contoller or new foot pedal pot control. I always keep a new board in stock myself-the foot contol pots seem to hold up longer these days. I have a spare foot petal so I can test the function by trading them out.This malfuction could be either one of these. I assume you mean the on off switch? I never had one of those fail. Let us know the outcome. Mark Link to comment Share on other sites More sharing options...
Wyndham Posted April 8, 2015 Author Report Share Posted April 8, 2015 Mark, I'm talking about the foot pedal Hi/Low pot ajustments inside the pedal. the low rpm pot seems not to adjust as you trim the low with turning from low/off to1.5 turns to max Wyndham Link to comment Share on other sites More sharing options...
Mark C. Posted April 8, 2015 Report Share Posted April 8, 2015 I got that-if the pot (that red and blue plastic screw wheel does not adjust it can be a new one or it can also be the circuit board in controller. As far as the hi/low there is a symbiotic relationship between them so try turning the hi down and then turn the low-They work together sort of speak.Adjust the hi lower then try the low-its counter intuitive. You may need this switch (potentiometer) or a new circuit board which also controls some speed issues-Now I'm guess inning it s new potentiometer. Mark PS I have worked on more of these that I want to admit, Link to comment Share on other sites More sharing options...
Wyndham Posted April 8, 2015 Author Report Share Posted April 8, 2015 Thanks, I'll work more on it tomorrow. Wyndham Link to comment Share on other sites More sharing options...
Mark C. Posted April 8, 2015 Report Share Posted April 8, 2015 I would call teck support -the e-mail will take to long. Mark Link to comment Share on other sites More sharing options...
Wyndham Posted April 8, 2015 Author Report Share Posted April 8, 2015 I've got 3 calls into them but no return call yet,oh well have a backup wheel so it could be worse. Thanks Wyndham Link to comment Share on other sites More sharing options...
neilestrick Posted April 8, 2015 Report Share Posted April 8, 2015 Brent wheel tech support is really difficult to get in touch with. It usually takes me 2-3 days. I'd go ahead and order new pedal guts to try. It's cheap, and worth having a spare on hand if it turns out to be the controller. Link to comment Share on other sites More sharing options...
Mark C. Posted April 8, 2015 Report Share Posted April 8, 2015 The only way I get thru to brent is repeated calls-they have rarely called me. I'm a bulldog who never gives up.Just put them on speed dial. I will also agree with Neil and just buy the pedal guts-heck if its not that I'll take it off your hands as a spare myself.I have a spare motor pedal and control board-in fact its all there as it came off a model b off e-bay. (not doing business only talking about it) Mark Link to comment Share on other sites More sharing options...
Mark C. Posted April 11, 2015 Report Share Posted April 11, 2015 Any news on a solution? Mark Link to comment Share on other sites More sharing options...
Wyndham Posted April 12, 2015 Author Report Share Posted April 12, 2015 Finally got through but the tech was not that well versed and said the foot pedal controller board was likely out. I asked for the head tech, Bob, but Bob was out at the dentist. The controller board doesn't have an obvious burned component on the board but that's all I can tell till I can find out if there is a meter reading I can take on the board to tell if it's bad Board replacement is $150-175, will find out when I get them the ser #. If the date is the last 4 digits, that will be 12,03 dec of 03 Will learn more this week Thanks Wyndham Link to comment Share on other sites More sharing options...
Mark C. Posted April 12, 2015 Report Share Posted April 12, 2015 Bob knows his stuff-it sounds like I said the curcuit board or the foot pedal guts If they tell you how to check the board I would like to know how. I just did some curcuit board soldering on a battery jumper board. Mark Link to comment Share on other sites More sharing options...
Wyndham Posted April 12, 2015 Author Report Share Posted April 12, 2015 Will do. I too want to know more of what's going on with my equipment Wyndham Link to comment Share on other sites More sharing options...
Mark C. Posted April 12, 2015 Report Share Posted April 12, 2015 I think there was a thread on the rectifier change out a few years back on this contol board-You may want to hunt that thread down? Mark Link to comment Share on other sites More sharing options...
Wyndham Posted April 13, 2015 Author Report Share Posted April 13, 2015 Going to send the foot pedal and controller box to Amaco c/o Bob for repair. no other choice it looks like, oh well, stuff breaks Wyndham Link to comment Share on other sites More sharing options...
Mark C. Posted April 14, 2015 Report Share Posted April 14, 2015 I sent my old one in a few years ago to Bob-never washed the foot pedal it was a mess. He called and said he loved it was being used so much When it came back he had replaced the pedal with a new one at no charge. So do not clean it up. Mark Link to comment Share on other sites More sharing options...
Wyndham Posted April 14, 2015 Author Report Share Posted April 14, 2015 I love it Ha Wyndham Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.