Jump to content
Sign in to follow this  
Stephen

Adding Elect for 3 Kilns

Recommended Posts

I just wanted to share my experience hiring an electrician to add dedicated plugs for three kilns outside of San Antonio and using a San Antonio, Tx company. 

I needed 3 plugs. Two 50 amps and one 20 amps. My Main electrical panel is on the outside wall of the the garage wall I needed them on so the run is through the wall behind the panel and a couple of feet. Walk up access to both inside and outside, no brick and no attic access needed. Panel was full and needed a 2nd box attached next to it.

In the area I am in there is a lot of new home building and I definitely got the impression that everyone is busy. I went out for 3 bids. One didn't respond for a week, one bid $875 (including parts) and the third was $1234 including parts. The $875 bid was a very local company that did not come see the job but just bid it from pictures. He was slow to respond to a couple of questions and when he did it was one liners that were a bit cryptic. He might well have been doing it from a phone. I waited for a few days for answers to my questions and then picked the $1234 company and set up the job and signed the acceptance paperwork.  The $875 guys responded the next day with good answers to my questions and the $875 was firm and included parts but since I had already agreed to the other bid I stuck with them. 

I'm not an electrician but I built a 300' studio building on my last property in the NW and I dug the 100'  "L"  trench, hung the sub-panel and ran all the inside wire, installed all the receptacles (12 110 plugs and a 50amp one) and paid an electrician $80 an hour (about $1200) to inspect everything, actually run the outside line in the trench and power up the new panel and sign off on it all for building inspection.

Based on that experience I honestly thought this job was about 3 hours on the outside with the sub-panel.

It took almost exactly 3 hours but I think he stopped several times to do other things.  

The 3rd company finally responded after all was setup as well and they said they would do it for $90 and hour plus parts (and I could buy them if I wanted).

My take away from this was I got impatient and will never hire another electrician for a flat rate bid again. They just pad the bid too much to make sure they don't blow it. I get that a lot of electricians don't want to mess with residential but I now know that if you are patient you can find one that will work by the hour and I think you will always come out ahead. Works well for them too as they just come do the work and don't have to worry about some gotcha blowing the bid.

I personally think that anything at or south of $150 and hour is a fair rate for this type of work. I say this based on doing the bulk of one and watching two others. The guy that bid mine, in a discussion over flush mounting my plugs, flat out told me he bid it at 6 hours and they had the equipment at $500

If I had bought my own equipment and hired the hourly company i would have paid about $200 for the parts at Lowe's and $270-$360 for labor so about half what I paid by bid.

Still I was impressed that I got 2 fairly reasonable bids. The guy that did the work was very nice and did a very nice, clean job and best of all all of our kilns are ready to be hooked up and our new studio finally up and running! 

 

 

 

 

 

 

 

Edited by Stephen

Share this post


Link to post
Share on other sites

A good electrician is worth every dime, however I do not like flat rate bids. Chances are they are making more than their regular hourly rate when they bid it that way. When I give quotes for kiln repair, I break it down parts and labor, and give an estimate on the labor, and a 'not-to-exceed' rate.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×

Important Information

By using this site, you agree to our Terms of Use.