Jump to content
Sign in to follow this  
Tamas

Iron Reactive Transparent Glaze

Recommended Posts

Tamas    0

Hello Everyone,

 

 

I was looking at this commercial glaze: https://www.scarva.com/en/Scarva-GZ2214-Iron-Reactive-Glaze/m-5060.aspx

 

and was wondering if you could tell me which component/property of this glaze made it 'iron reactive'? I would love to locate a glaze recipe with the same effect that I could try, or develop a glaze on my own.

 

Thanks!

 

 

Share this post


Link to post
Share on other sites
Tamas    0

That is strange, when I click on it it takes me straight to the specific page. Apologies.

Anyway, the glaze is the Scarva GZ2214 Iron Reactive stoneware glaze.

 

Share this post


Link to post
Share on other sites
Joseph F    866

5060.Jpg

 

The website is bonkers, but I did a little googling and found this image. I assume it is the one your talking about?

Edited by Joseph F

Share this post


Link to post
Share on other sites
Tyler Miller    331

Joseph,

 

that website is indeed bonkers. It seema they want you to navigate through their store front whether you need to or not.

 

Tamas,

 

that look can be achieved a number of ways by a studio potter. Jonathan Walburg wedges iron-bearing lake superior sand into his porcelain to achieve a similar, but more speckled effect under his maple ash glaze base. But that precise variegated look is likely due to a strong flux (lithium?) to pull out the iron and some rutile--which likes to variegate.

Edited by Tyler Miller

Share this post


Link to post
Share on other sites
Tamas    0

Thank you, guys - indeed that was the glaze I was referring to. Yes, I know I can get a speckled look in various ways, I was just curious what wizardry they used to achieve it in the glaze.

 

Here's what Scarva says about the glaze:

 

 


GZ2214 is a cone 9 stoneware glaze developed to react with iron in the clay body.  Bodies with a higher iron content will react more readily with the glaze, creating a beautiful reddish brown effect highlighting iron speckles. Bodies with lower iron content will yield a whiter glaze with fewer flecks.

• Firing range: 1200-1280°C
• Finish: Glossy
• Leadless

The image shown is of SP90 Burren and of SW10 V9A showing how the glaze reacts with different amounts of Iron in the clay bodies.

Edited by Tamas

Share this post


Link to post
Share on other sites
Chilly    331

The link worked perfectly for me, perhaps it is UK biased?

Share this post


Link to post
Share on other sites
dhPotter    148

Tamas,

 

This glaze looks like a Nutmeg. Bill Van Gilder has a nutmeg recipe.

 

Tyler, his recipe has Spodumene 23.3%

Share this post


Link to post
Share on other sites
Sputty    73

The link worked perfectly for me, perhaps it is UK biased?

 

It works fine for me too, in France.

The 'problem', if it is such, is confined to people who visit the site from countries other than European ones. If you tell the site you are from the US, it re-directs to the index page. From anywhere in Europe, it's fine.

Share this post


Link to post
Share on other sites
neilestrick    1,381

Here's one I used to use:

 

Custer            28.30

Spodumene   18.87

EPK                24.53

Dolomite        20.75

Whiting            1.89

Tin Oxide         5.66

Cone 10 Reduction

Edited by neilestrick

Share this post


Link to post
Share on other sites
Marcia Selsor    1,301

The link worked for me too. As Neil points out with his reduction glaze, iron is reactive in a reduction firing. The reduced oxygen in the atmosphere pulls oxygen in iron oxide bringing the iron to the surface of the glaze...at least visibly. If the glaze in the photo is fired in an oxidized atmosphere, then they  have developed a nice commercial glaze for oxidation.

 

Marcia

Share this post


Link to post
Share on other sites
Tamas    0

The link worked for me too. As Neil points out with his reduction glaze, iron is reactive in a reduction firing. The reduced oxygen in the atmosphere pulls oxygen in iron oxide bringing the iron to the surface of the glaze...at least visibly. If the glaze in the photo is fired in an oxidized atmosphere, then they  have developed a nice commercial glaze for oxidation.

 

Marcia

 

That makes sense, thank you, Marcia. I fire electric, so this particular solution is not an option for me then.

Share this post


Link to post
Share on other sites
neilestrick    1,381

With enough iron in the clay, and a good glaze, you can get a very similar effect in oxidation. It just takes more iron in the clay to get the effect. I've got some cone 6 oxidation glazes that I modified from cone 10 reduction, and on a speckled brown cone 6 clay they are nearly identical.

Share this post


Link to post
Share on other sites
Tamas    0

With enough iron in the clay, and a good glaze, you can get a very similar effect in oxidation. It just takes more iron in the clay to get the effect. I've got some cone 6 oxidation glazes that I modified from cone 10 reduction, and on a speckled brown cone 6 clay they are nearly identical.

 

Neil, that is interesting. I will look for and try out some clays to see if I can get close.

Share this post


Link to post
Share on other sites
preeta    80

Neil do you mix your claybody for the right iron or do you go with a commercial body?

 

Could you use iron engobe or slip or even an iron wash over non iron clay to get similar response?

Share this post


Link to post
Share on other sites
Min    784

If you are looking for that rusty red with cream look for cone 6 oxidation look for recipes containing both tin and iron. There are a quite a number of them on this link

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×