Jump to content

Recommended Posts

vlao1984    0

Hi Everyone,

 

Wondering if anyone has put an electric kiln in garage. I'm aware of the fumes, flammables, and other risks but my primary purpose is to just do bisque fires. I don't want to install vent hoods and other ventilation parts and just want to open my garage doors.

 

Thoughts and inputs are greatly appreciated. 

Share this post


Link to post
Share on other sites
Tim Allen    8

That's where our electric kiln is located, in a detached garage. No vent system in the current installation, we just open the door. We only use it for bisque

Share this post


Link to post
Share on other sites
Marcia Selsor    1,301

Mine are in a wooden shed 16 x 11. I don't have exhaust systems. Just open the doors.

I am working on my separate raku area

 

Marcia

Share this post


Link to post
Share on other sites
bciskepottery    925

Mine is in attached garage, but I have it vented (I fire both bisque and glaze). I also crack the garage door open during overnight firings to vent heat and fumes. I had an electrical subpanel installed to support the kiln and rest of studio.

Share this post


Link to post
Share on other sites
Pres    896

Garage here in PA, fire all year round, no direct ventilation, although I have a chimney flue with opening directly next to kiln. In Winter you can tell it is drafting. No problems with fumes, as when firing I do not hang out in the shop. When cooling, I work on new pieces in the Winter. 

 

 

best,

Pres

Share this post


Link to post
Share on other sites
Joseph F    865

Mine is in attached garage, but I have it vented (I fire both bisque and glaze). I also crack the garage door open during overnight firings to vent heat and fumes. I had an electrical subpanel installed to support the kiln and rest of studio.

 

I do exactly this as well. It works wonderfully. I put the pipe out the crack of the garage door. During the really cold winter, I have old comforters I bought at the goodwill and I duct tape them in a long roll. I push them against the door to prevent too much cold air coming into my studio. I only do this when it is around 30-40 degrees. 

 

I don't have an extra subpanel installed though. My electrician said I had plenty of room on my breaker box. The previous owners had it upgraded, so that was nice of them. 

Share this post


Link to post
Share on other sites
tricetra    4

My partner Buillt my studio in one side of our duck barn and my kiln has no extractor. When I set of kiln I leave the window and unblock a wall pipe to vent and stay out of the studio (Mainly do overnight firings). I then can work in there during the cooling down period when the kiln keeps the room toasty ;-).

Share this post


Link to post
Share on other sites

Garage here too.

No vents - just fans and open doors. Never had any problems except the time a drycleaner bag blew onto the exterior of the kiln.

Marc

Share this post


Link to post
Share on other sites
Johnmicheal    0

I think it depends more about what you plan to have in the garage with it. Electric boxes are commonly found in the garage or upgrading with a sub panel should make wiring fairly straight forward. Garages, even if they are attached, are supposed to not share fumes to the house, i.e. Gas or exhaust from your car. All you need is your flat concrete floor, enough space around the kiln, 18" is recommended, and alittle ventilation, 10$ box fan in a window, or open your garage door, and your set. The biggest hazard is anything that blows in and lays on your kiln and catches fire, newspaper, wrapping paper, lots of leaves, ect. Checking on your kiln while your firing, priceless. If it's a manual firing, a nice chair for the last hour.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×