Jump to content
Sign in to follow this  
flowerdry

Shimpo Rk 2 Vibrating

Recommended Posts

flowerdry    128

I am trying to figure out what is going on with the Rk2 at the community studio where I teach. It vibrates enough that it makes your whole leg feel weird if you leave your foot on the pedal. Wheel head runs true and does not vibrate. I disconnected the cone from the ring plate (what a weird set up!) and the motor does still vibrate just slightly. I had one very handy electrician take a look and he said check the bushings in the motor. (Turns out there are no bushings in the motor.) Someone who knows a lot about wheels told me it had to be the bearings based on my description of the problem. He recommended a shop where he has taken wheels.

 

I took the wheel there and they charged me $80.00 to check out the motor and tell me it wasn't the problem, and now I still have a wheel that vibrates. The belt and the ring plate appear to be ok, but I guess I'll try replacing them. Before I spend more money, has anyone out there seen this problem or have any suggestions?

Share this post


Link to post
Share on other sites
Mark C.    1,796

You must  pinpoint where the vibration is coming from-if the motor is causing it does the cone drive amplify it??

Best to turn it on its side and operate and see whats going on.

You also can call shimpo and talk to a Teck-this may be the best time spent on this.

 

Myself I do not like the cone drive system-to static and cumbersome for me. They do look cute.

Share this post


Link to post
Share on other sites
flowerdry    128

Mark, I did do that. Everything stopped vibrating when I disconnected the motor from it's load, except a very slight vibration in the motor. That, and the advice of the two other people is what caused me to confidently bring the thing to a motor shop.

Share this post


Link to post
Share on other sites
Mark C.    1,796

Its been many decades where I have laid eyes on that cone drive system-is there any chance the ring/pulley is bent?Or the cone has a flat spot on it?

Share this post


Link to post
Share on other sites
flowerdry    128

Ring pulley definitely not bent.  Cone looked good, but I will check again to be sure.  Thanks so much for spending some brain cells on this Mark.  I will try calling Shimpo on Monday.

Share this post


Link to post
Share on other sites
Mark C.    1,796

I do recall years ago about a cone with a flat spot on it-buts thats I can recall.

Share this post


Link to post
Share on other sites
RonSa    188

Remove the belt and run the motor, does it still vibrate?

 

If not, take a closer look at the v-belt. Bend the belt, it should have some flex to it. If it is somewhat stiff or there are cracks present replace the belt.

 

The wheel head should spin freely now without the belt connected. Is it spinning smoothly and quietly?

 

Is there a rumbling noise when the belt is connected and the wheel head is spinning?

 

If so,  check to see if there is any debris between the cone and the ring plate.

 

Next closely inspect the cone, I don't know what material Shimpo uses to make their cones but it should be smooth without any flat spots or bumps that can cause vibrations.

 

Now closely inspect the ring, are there any imperfections? Typically the rings are meant to be replaceable.

 

Good luck

Share this post


Link to post
Share on other sites
Dale pots    7

If the pedal was pushed down & left that way while not in use it will put a flat spot on the cone. It may return to normal if it's not too old & hard. Other than that the belt could be separating, which could be hard to tell without removing it & turning it inside out (sort of speak). While the belt is off see if the motor pulley moves side to side with your hand (bearing), then turn it on & listen for a bearing. The worse thing is if the rubber suspension washers that hold the whole motor are wasted, they are integral with the bolts. Mine did that & I tried to work around that & never was the same. But it was 30 years old at the time. So I went out & bought a Rolls Royce (Brent).

         Lets hope yours is just a belt!       

Share this post


Link to post
Share on other sites
What?    82

Here is a picture of the bushings. The ringcone may not be true. flywheel issue? Not sure about the belt. Call shimpo is best advice. Good fast service. The only problem is parts get expensive but $200 and you have another 20 years of life. I have Two. One is the Rincone Poppet. You did not mention which one. These things are tanks. Good luck.

post-66695-0-63714600-1492489346_thumb.png

Share this post


Link to post
Share on other sites
millerwood    0

I replaced a cone on my rk2 which had lost some of the hard chrome plating near the small end.  In doing so I also replaced the bearings in the motor, and dial indicated the cone to ensure it runs true.  A bent motor shaft or bad bearings in the motor are suspects I think.  Is your cone straight sided or radiused like the picture?

 

Larry

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×