Jump to content


  • Content count

  • Joined

  • Last visited

About Min

  • Rank
    Advanced Member

Profile Information

  • Gender
  • Location
  1. glad you are back! congrats on the new house and studio!
  2. I think I got it bassackwards in my other post, I think if you cut the foam into squares and glued them onto a backing piece it would make more sense. Could you design it so a wedge of clay went under the grid so the whole thing was on a slight slope? Kiln wash the wedges and make them of raku type clay so you could reuse them? Just throwing out ideas, might all be utter garbage.
  3. Was thinking about this when I was out this morning, how about cutting craft foam into an open grid, as the walls are on the grid, hot glue gun it onto a full sheet of foam. Maybe stack 3 or 4 grids to make a deep enough impression. Some plastic film or a piece of pantyhose on top of it, then your slab on top of it and run it through the slab roller? dunno, might work? This stuff.
  4. Don't make the base and the lid separately, make one box the total height of the finished box then cut the top off and inch or whatever down from the top. That way the lid and base will flow together smoothly. I would add the base and top to the square "tube", round the corners then make a registration (key) mark then cut it. Make sense?
  5. I would make them with the 90 degree corners to start with, bevel the joining edges so there is more surface area to make a strong joint then add a very thick coil on the inside of the corners, when leather hard rasp down the 90 degrees to round them off the way you like. I would make the entire box as one piece so the lid will fit well then cut off the top section and add a flange to the lid or the base. I would also make some sort of decorative mark as a key on the outside so you know which way round the lid fits.
  6. In addition to knowing the hot and cold spots in your kiln (mostly if you have a single controller) I find cones are really beneficial when using a new kiln, changing firing program, after changing thermocouples or changing controllers. Once everything is calibrated then I find they are useful to use to verify firings, I don't put them in every load. I also use them when doing a lot of glaze tests in a firing, I want to know fairly accurately what cone the glaze tests got to.
  7. Dipping Pots into glaze

    Yeah, if the dry glaze cracked it will crawl when fired. If they were mine I would wash them off and redo them for the next load when they have dried out. Or if you really have to do them now rub down the cracked areas so the glaze is thinner.
  8. Thanks, I always get their names mixed around, I went back and corrected it in my post.
  9. Thank you for the link to the pen Mea! I just ordered one. Amazon US was 9.99 plus 5 for shipping to Canada, Amazon Canada price is 28.56 plus shipping ( ships from the US). Crazy but typical!
  10. Just in case you haven't read it yet the Tom Turner article on Chemically Reduced Copper Reds in Oxidation has all sorts of tantalizing clues, like "Chemicals such as tin, zinc, magnesium, iron, phosphorous, sulphates and of course any material containing carbon are hungry for oxygen and will help reduce the glaze colourants as they melt" Also, "I found that as the silicon carbide size became smaller, there was more glaze melt, less surface texture from the glaze bubbling while giving off oxygen during the chemical processes and weaker reduction." BTW in oxidation firings I've found cobalt, copper and manganese act as fluxes.
  11. Oh, that's what I couldn't think of! Knew it reminded me of something. I can totally see making these as a learning exercise for new potters but was thinking in terms of selling them. So many customers saying they are looking to downsize or at least not add to what has already filled up their cupboards that a specialized pot would be harder for me to sell. Not a drinker so I don't really get the whiskey cup, does the spiral in the middle start going round and round after a few?
  12. Looking at the design of those and couldn't help but wonder what else you could use them for. Thought it somewhat resembles a lemon reamer. If the middle bit was a titch wider at the base you could carve sharp channels into the center part and if one of the scallops on the rim was sharpened a bit it could be the pour spout. I like having more than one use for pots, it's got me thinking....
  13. Sometimes the simplest things are the most useful aren't they? I use a microfiber cleaning cloth that is meant for eyeglasses, really don't like the slimy feel of a chamois.
  14. yikes, all guesses... 4,3,1,1 We need Jed to answer these!
  15. If you only have a bit that needs a spray these things work okay. (or if you don't like huffing and puffing) I used one before I got my spraybooth set up, used outside. Wouldn't use them to cover entire pots with glaze but for highlights they are good and very simple to use. For the question of the week I would have to go with my waterfall spray booth. Got a brand new fiberglass shower stall for free when we had our yearly "throw out anything you don't need" day and we went scrounging and found it. Used pump, some mesh that we had to buy plus a few plumbing bits and pieces, came in well under a 100-